පැන්ට්රි කබඩ් එකක් සෑදීමට අවශ්ය ද්රව්ය || What are the want when making pantry cupboard .
................................................................................................................................
#india #aluminum #pantry
What are the want when making pantry cupboard,use full cupboard,aluminium pantry cupboards,india pantry cupboards,sri lanka pantry cupboards,top ten pantry cupboards,most beautuful pantry cupboard,kitchen cabinet,kitchen organizer,low cost pantry cupboard,how to make pantry cupboard,how to install pantry cupboard,pantry cupboard making video,how its make,easy die,closets,pvc pantry,eco board pantry,kitchen cupboard,kitchen cabinet idea,morden pantry
Hello and welcome to the RN Homes YouTube channel. Today we are talking about the second video in the Pantry Cupboard video series. So don't miss these videos. These videos are linked one by one. Finally, the process goes until the estimate is made. Today we are talking about what are the ingredients used to make a pantry? Because in order to make this estimate, we need to know the prices and names of these items and how much they will cost. If I did the introduction right, this is the first lesson on what ingredients are needed for a pantry. So let's go to the video. Subscribe to our channel today to get videos like this. Click the bell icon and you can watch a video as soon as we post it.
First, let's make the structure of the pantry cupboard. For this we use aluminum pantry cupboard, I am talking about aluminum box bar and then we want to use box bar two by one, one by one, one and half by one box bar. Remember here to use two by one bar for the grant structure. If that happens, it will be easier for us to connect the bars and connect the hinges of the door channels. Otherwise, you can use a box bar to connect it, but problems arise when connecting the hinges. Therefore, the first structure is two by one box bars.
If not, make sure to make the facing frame with two by one box bars.
After that we need 3/4 * 3/4 thick angle bars to rivet the structure and fix the bars. After that 1/2 * 1/2 L bar is required. And a U bar of 5/16 * 3/8 is required. Contact the board. Then you need pantry door bars. So those are the bars we need from aluminum.
Then after taking the hardware items, we need pop rivets to connect the frame with 5/32 * 1/2 pop rivets. I've done a whole tutorial on those rivets and I'll post them on top of that card. Look at that, guys. Then you need 1/8* 1/2 pop rivet and 1/8* 1/4 pop rivet. Next you need a drill bit, 1/8 bit, 5/32 bit, and a number six Hilti bit, and a number six wall plug. Number eight requires 1 1/2 or 2 CSK nails.
That's all you need from hard-wear items.
After that we use 3mm cladding board for this. Here it is very good to use white board inside the pantry. Then when you open the pantry, you will get good light. Apply boards of the corresponding color to the door frames.
Now it is often better to use fiber board than cladding board, because the aluminum layer of the cladding board peels off after a while. After that we need a bracket made of iron to connect the door.
Next you need drawer rails. We call these drawer rails and drawer bearings. In this, the railing that comes to the key board of the computer desks comes first. It is the basic railing. The rails run with the wheels. After that, there is a railing that runs with iron balls. After that, there is a hydraulic railing. Most of the time we use this railing. This Ken drawer can bear a good weight and has a good finish. After that, when you get the hinges, you can put normal hinges, if not, you can put hydraulic hinges. This one also comes without hydraulics. Next, we need wool felt, which we usually attach to the back of the pantry door. We use this felt to seal the door well and prevent insects from entering. These are available from four inches to 12 or 14 inches. Always use a larger handle for a better finish. Then magnets are used to seal the door well.
Additional silicon is used. Here we use as accessories, one item is the cutlery tray that comes in the drawers, we use this tray to put things like forks, etc. Then the plate rack. And another basket is coming, a rack made of white iron. After that, the bottle rack, this rack is used to put wine glasses and wine bottles. After that comes the dustbin bucket, which is usually installed under the sink. After that, there is the double bowl sink and the single bowl sink. There is the cooker hood. Then there is the four burner stove or the gass hob. That's what you are saying, we are including the extras. So I put them together with the pictures so that if we do these things, we will know about them.
After that in the lesson we will take a pantry and draw a general sketch and see how we order the items and tell the price per foot and how to present the quotation to the customer in the next lesson Thank you very much.
Информация по комментариям в разработке