How to Replace a 2007-2013 Chevrolet Silverado Fender (1500/2500/3500) | Remove & Install | ReveMoto

Shop painted Chevrolet Silverado fenders here: http://bit.ly/1500fender
These giant Silverado fenders are the same as every other GMC truck. A big fender with a big shelf and a lot of bolts. Let us show you how to remove this in our detailed video.

Follow Us on
FB:   / revemoto  
IG:   / revemoto  
Twitter: https://twitter.com/revemoto?lang=en.

0:00 Start
0:47 Tools needed
1:49 Remove the fender liner
3:26 Remove the headlight
We had to remove the bumper end cap since it was pushing up on the headlight
5:54 Disconnect the headlight wires
6:20 Remove the battery
6:52 Remove the intake manifold
7:12 Remove the coolant reservoir
7:37 Remove the battery shelf
9:38 Remove the Intake plate
10:18 Detach the hood support bracket
10:57 Remove the bottom fender bolt
11:21 Remove the bolts between the door
12:04 Take the front bolts underneath the headlight
12;40 Take off the top corner bolts
13:12 Replace all the fender accessories
13:25 Mount the fender
14:30 Insert the bolts to hold the fender in place
16:42 Secure the hood bracket
17:50 Install the trays for the battery
18:19 Insert the battery
19:38 Attach the fender support
20:16 Install the intake and coolant reservoir
23:31 Tighten all the bolts
25:02 Check the alignment or spacing
25:43 Install the headlight
30:35 Install the fender liner
32:38 Outro

This fender is very similar to Tahoe, Sierra, Escalade, and Yukon trucks and SUVs.
These are not your typical fenders, they have an inner fender. What's that?! The fender is not just a panel like most vehicles, but rather has a long inner shelf that extends into the engine bay where other components are bolted to the fender. Yes, It can be a pain but we're here to help.

Subscribe: https://www.youtube.com/c/Revemoto?su...

You're only dealing with bolts, so knowing what to take off is key. This video is rather long but we shortened it as much as we could. For the right-passenger side fender, the battery, coolant reservoir, and air intake sit on top of the inner fender or fender shelf. Once these items are removed, you can take off the steel plates they sit on-off.

After this step, the only thing attached to the fender should be the hood hinge, fender liner, and headlight. The headlight and fender liner is pretty standard when changing a fender. GMC-Chevy decided to create the fender so large that the hood hinge has to bolt onto the fender. This is not typical for most vehicles. You have to prop the hood up to remove the hood hinge bolt.

Finally, remove all the bolts holding the fender to the frame, and you are almost done. Now, you have to transfer any hardware from the old fender to the new and work your way backward to install the new fender.

Source: https://www.revemoto.com

________________________________________________________
#Silverado #ChevySilverado #DIY #Chevrolet #paintedautoparts #Chevy #highquality #HowTo #revemoto #silverado1500 #1500Chevy #silverado2500

DISCLAIMER: While ReveMoto tries to make the information in this video as accurate as possible, we make no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself (DIY) projects entail some risk. It is the sole responsibility of the viewer to assume this risk. ReveMoto is not responsible or liable for any loss, damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.