SeaDoo Engine Gateway

If you like these videos, please subscribe. How to get your Garmin EchoMap UHD to display engine data on a SeaDoo Switch. Needs a NMEA 2000 network. This video will show how to install the NMEA 2000 network and the Yacht Devices Engine Gateway. SEE COMMENT BELOW ABOUT FUEL LEVEL. Check video on Yacht Deices Tank Adapter for fuel level. If this has helped, please like and subscribe.

Yacht Devices Engine Gateway: https://amzn.to/45pgszH
Adapter Cable: https://yachtdevicesus.com/collection...
Garmin NMEA 2000 Starter Kit: https://amzn.to/3pEyZYF
Garmin NMEA 2000 T Connector: https://amzn.to/3BnpXlb
MicroSD Card: https://amzn.to/42P56D6

YDEG.txt -Copy the text below and paste to your microSD card as the YDEG.txt file. Copy all to where it says # END OF FILE. For some reason, YouTube makes everything that is supposed to have a "#" in front of it Bold. So anything in bold, put a # in front of that line.

Current configuration of Yacht Devices Engine Gateway YED-04
Firmware: 1.36 05/5/23
https://www.yachtd.com/downloads/#yde...

If no data displayed then change CAN_SPEED to 250
ENGINE_CAN_SPEED=500

ENGINE_0 changed to 1 and ENGINE_1 changed to OFF

ENGINE_0=1
ENGINE_1=OFF
ENGINE_2=OFF
ENGINE_3=OFF
ENGINE_4=OFF
ENGINE_5=OFF
ENGINE_6=OFF
ENGINE_7=OFF
HOURS_OFFSET=0

If fuel rate and other data not available, change BRP_ROTAX from ON to HANDSHAKE
BRP_ROTAX=ON
SMARTCRAFT=OFF
VOLCANO=OFF
EDC2=OFF
MEFI4B=OFF


Reset when switching SMARTCRAFT or MEFI4B settings, use CALIBRATE_TRIM
TRIM_ZERO=28708
TRIM_STEP=128

EXHAUST_TEMP=ON
INTAKE_MANIFOLD_TEMP=OFF

NMEA_BATTERY=KEYSWITCH

BATTERY_0=0
BATTERY_1=1
BATTERY_2=OFF
BATTERY_3=OFF
BATTERY_4=OFF
BATTERY_5=OFF
BATTERY_6=OFF
BATTERY_7=OFF

NMEA_ALTERNATOR=KEYSWITCH

If no display, change to FUEL=DIESEL

FUEL=GASOLINE

FUEL_0=0,PORT
FUEL_1=0,STARBOARD
FUEL_2=OFF
FUEL_3=OFF
FUEL_4=OFF
FUEL_5=OFF
FUEL_6=OFF
FUEL_7=OFF
FUEL_8=OFF
FUEL_9=OFF

TANK_CAPACITY_0=DEFAULT
TANK_CAPACITY_1=DEFAULT
TANK_CAPACITY_2=DEFAULT
TANK_CAPACITY_3=DEFAULT
TANK_CAPACITY_4=DEFAULT
TANK_CAPACITY_5=DEFAULT
TANK_CAPACITY_6=DEFAULT
TANK_CAPACITY_7=DEFAULT
TANK_CAPACITY_8=DEFAULT
TANK_CAPACITY_9=DEFAULT

TANK_CALIBRATION_0=OFF
TANK_CALIBRATION_1=OFF
TANK_CALIBRATION_2=OFF
TANK_CALIBRATION_3=OFF
TANK_CALIBRATION_4=OFF
TANK_CALIBRATION_5=OFF
TANK_CALIBRATION_6=OFF
TANK_CALIBRATION_7=OFF
TANK_CALIBRATION_8=OFF
TANK_CALIBRATION_9=OFF

MDI_PROP_MESSAGE=ON
MDI_AUX_MASK=000000
MDI_SYS_FAULT_MASK=000000

ALERT_0=OFF
ALERT_1=OFF
ALERT_2=OFF
ALERT_3=OFF
ALERT_4=OFF
ALERT_5=OFF
ALERT_6=OFF
ALERT_7=OFF
ALERT_8=OFF
ALERT_9=OFF

ALERT_WARN1_MASK=000000
ALERT_WARN2_MASK=000000
ALERT_POWER_REDUCTION_MASK=000000

NMEA_ALERT_MASK=FFFFFF

TRANSMISSION_0=3
TRANSMISSION_1=4
TRANSMISSION_2=OFF
TRANSMISSION_3=OFF
TRANSMISSION_4=OFF
TRANSMISSION_5=OFF
TRANSMISSION_6=OFF
TRANSMISSION_7=OFF

TRANS_ALERT_0=OFF
TRANS_ALERT_1=OFF
TRANS_ALERT_2=OFF
TRANS_ALERT_3=OFF
TRANS_ALERT_4=OFF
TRANS_ALERT_5=OFF
TRANS_ALERT_6=OFF
TRANS_ALERT_7=OFF
TRANS_ALERT_8=OFF
TRANS_ALERT_9=OFF

TRANMISSION_ALERT_MASK=1F

WATER_DEPTH_OFFSET=OFF
WATER_SPEED_CORRECTION=OFF
WATER_TEMP_OFFSET=OFF

PASS_PGN=OFF
PASS_ADDR=AS_IS

J_PASS_PGN=OFF
J_PASS_ADDR=210

For ENGINE_0 or TRANSMISSION_0, data instance +1 will be used for ENGINE_1, etc. SUBSTITUTE_BOOST=OFF
SUBSTITUTE_FUEL_PRESSURE=OFF
SUBSTITUTE_OIL_PRESSURE=OFF
SUBSTITUTE_OIL_TEMP=OFF
SUBSTITUTE_CLNT_PRESSURE=OFF
SUBSTITUTE_CLNT_TEMP=OFF
SUBSTITUTE_TRANS_PRESSURE=OFF
SUBSTITUTE_TRANS_TEMP=OFF

End of file