Sub 250g five inch quad with Shark Byte? Ummagawd 2Fiddy complete build and setup guide!

Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: https://www.fpvknowitall.com/ultimate...

SUPPORT ME ON PATREON at: http://bit.ly/2Ep5Sia

THIS IS MY FULL TIME JOB. Here are other ways that you can support me: https://www.fpvknowitall.com/support-me/

---

Ummagawd Crew FB group: https://www.facebook.com/groups/ummag...

---

I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.

Ummagawd 2Fiddy frame
* Ummagawd Store - https://bit.ly/3oGD48j
* RaceDayQuads - https://bit.ly/3D3plzZ
* GetFPV - https://bit.ly/3F8SCuY
* Pyro-Drone - https://bit.ly/3uttr1m
* NewBeeDrone - https://bit.ly/3Fdg61W

Ummagawd Aerolite 2004 motor
* Ummagawd Store - https://bit.ly/3inzsrm
* RaceDayQuads - https://bit.ly/3Fdo23c
* Pyro-Drone - https://bit.ly/3uEDEYY
* GetFPV - https://bit.ly/3F4vq13

iFlight Beast F7 AIO FC
* GetFPV (45A version) - https://bit.ly/2Y9OwCl
* Pyro-Drone - https://bit.ly/3yjFWyt
* NewBeeDrone (45A version) - https://bit.ly/3omOSQE
* Banggood (55A version) - https://bit.ly/3D2maZo

Foxeer Digisight camera for Shark Byte
* GetFPV - https://bit.ly/3mjRVX4
* Pyro-Drone - https://bit.ly/3l2SWTS

HQ T5x3 prop
* Ummagawd Store - https://bit.ly/3irTbGF
* RaceDayQuads - https://bit.ly/3D10j4w
* Pyro-Drone - https://bit.ly/3uwQyrE
* NewBeeDrone - https://bit.ly/3D3ELEl

Scout HD goggle with built in SharkByte receiver module
* Rotor Riot - https://bit.ly/3kk11SO
* GetFPV - https://bit.ly/3B93Wo5
* Pyro-Drone - https://bit.ly/3B4eVzp
* NewBeeDrone - https://bit.ly/3D7RPZg
* Banggood - https://bit.ly/2YgXgGI

Shark Byte RX5.1 receiver module
* Rotor Riot - https://bit.ly/3mSQKji
* GetFPV - https://bit.ly/3t8EpII
* NewBeeDrone - https://bit.ly/3orP8xB
* Banggood - https://bit.ly/3mUTAo8

Shark Byte TX5S.1 video transmitter
* Rotor Riot - https://bit.ly/2OxWC2g
* GetFPV - https://bit.ly/3bcLDmu
* NewBeeDrone - https://bit.ly/3orOQqv

MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.

-- TABLE OF CONTENTS --

0:00 - Intro and sample flight

   • Caddx Peanut fixes the biggest compla...   - My review of the Caddx Peanut

3:15 - Parts list
5:57 - Assemble the frame bottom plate and arms (the first time)
8:52 - Mount the flight controller (the first time)
12:03 - Solder on the main battery lead
13:31 - Install the motors and solder them to the FC
17:01 - My big mistake: arm screws not accessible when tall standoffs are used

https://amzn.to/3CYQ2FS - M2 screw assortment (take your pick)

20:36 - Why this SharkByte vTX is a bad choice for the 2Fiddy frame
21:48 - Solder on the receiver

   • You can flash this receiver over WiFi...   - Full setup guide for Happymodel ExpressLRS receiver

23:54 - Where should we mount the capacitor?

https://bit.ly/3lvpNzz - FETTEC spike absorber

26:04 - Install the camera in the camera plates
27:16 - Solder on the capacitor
30:15 - Smoke check
31:01 - Finish vTX installation/mounting
32:20 - Betaflight: set up receiver

   • Beginner Guide $120 FPV Drone How To ...   - How to set channel endpoints and channel mapping

35:12 - Betaflight: set up aux modes

   • Beginner Guide $120 FPV Drone How To ...   - How to set up aux modes

36:01 - Betaflight: set up configuration tab
38:36 - Flash ESC's to BlueJay to get bidirectional Dshot working

Bluejay configurator - https://github.com/mathiasvr/bluejay-...

40:35 - Betaflight: remap motors because FC is not facing forward
43:18 - Betaflight: check motor direction and reverse as needed
43:46 - Betaflight: adjust FC orientation
44:47 - Betaflight: adjust vBat max for use of HV batteries
45:15 - Betaflight: set up SharkByte canvas mode OSD

   • Shark Byte HDZero complete setup and ...   - My SharkByte full setup guide

48:06 - Configure SharkByte vTX and camera
50:06 - Betaflight: configure rates and PIDs

https://pastebin.com/TATZumW2 - Ummagawd PIDs CLI dump

51:25 - Select and install vTX antenna
53:52 - Finish installing the camera
54:58 - Add retention zip tile to battery lead
55:35 - Install Ummagrip battery pad
56:49 - Final weigh-in. Is it under 250g?!