Скачать или смотреть Powder Coat / Post Cure Oven Build using a Cabinet

The following steps will guide you through the construction of a post-cure / powder coating oven from a storage cabinet. Following its completion, we will conduct a temperature test to verify its performance and then proceed to post-cure a carbon fiber part to demonstrate its practical application.

1. Intro - 0:01
2. Step 1 (Remove Cabinet Doors) - 0:36
3. Step 2 (Measure Internal Dimensions) - 0:52
4. Step 3 (Cut Out Back Plate) - 1:26
5. Step 4 (Remove Sharp/Rough Edges (Back Plate)) - 1:56
6. Step 5 (Cut/Insert Insulation (Back Plate)) - 2:37
7. Step 6 (Insert/Secure Back Plate) - 3:19
8. Step 7 (Stuff Insulation (Top Plate)) - 5:54
9. Step 8 (Cut/Insert Insulation (Top Plate)) - 7:06
10. Step 9 (Insert/Secure Top Plate) - 7:52
11. Step 10 (Stuff Insulation (Bottom Plate)) - 8:31
12. Step 11 (Cut/Insert Insulation (Bottom Plate)) - 8:47
13. Step 12 (Insert/Secure Bottom Plate) - 8:58
14. Step 13 (Cut Out/Trim Side Plates) - 9:12
15. Step 14 (Cut Out Side Brackets (12)) - 9:53
16. Step 15 (Drill Rivet Holes for Side Brackets) - 10:31
17. Step 16 (Install RH Side Brackets (6)) - 11:19
18. Step 17 (Cut/Insert Insulation (RH Side Plate)) - 13:21
19. Step 18 (Insert/Secure RH Side Plate) - 14:03
20. Step 19 (Install LH Side Brackets (6)) - 15:02
21. Step 20 (Cut/Insert Insulation (LH Side Plate)) - 15:17
22. Step 21 (Insert/Secure LH Side Plate) - 15:23
23. Step 22 (Insert/Secure Pegboard) - 15:38
24. Step 23 (Cut Out/Trim Door Plates) - 16:41
25. Step 24 (Stuff Insulation (LH Door)) - 17:03
26. Step 25 (Cut/Insert Insulation (LH Door)) - 17:27
27. Step 26 (Install LH Door) - 18:08
28. Step 27 (Insert/Secure LH Door Plate) - 18:20
29. Step 28 (Stuff Insulation (RH Door)) - 18:53
30. Step 29 (Cut/Insert Insulation (RH Door)) - 19:00
31. Step 30 (Insert/Secure RH Door Plate) - 19:17
32. Step 31 (Install RH Door) - 19:22
33. Step 32 (Insert Washers (Door Corners)) - 19:26
34. Step 33 (Mark/Cut Out Heater Mount) - 20:51
35. Step 34 (Remove Sharp Edges (Heater Mount)) - 22:06
36. Step 35 (Drill Mounting Holes) - 22:34
37. Step 36 (Install Heater) - 22:46
38. Step 37 (Clean Door Edges) - 23:31
39. Step 38 (Install Smoker Gasket Seal) - 23:46
40. Step 39 (Install Thermocouple) - 25:09
41. Step 40 (Perform Temp Test) - 26:02
42. Step 41 (Apply Flexible Latex Sealant) - 28:08
43. Part Post Cure - 28:43

Products Used:
This video contains affiliate links for which I may receive compensation.
========== Oven Material ==========
1500 Watt Heating Element - https://amzn.to/41OE00S
Aobabo 42 Inch Storage Cabinet (759537612414) - https://www.target.com/p/aobabo-42-in...
18Ga [0.048"] Cold Rolled Sheet 4'x 8' (2) - https://www.metalsupermarkets.com/pro...
Aluminum 6061 Channel 1.000 X 1.000 X 0.125 (5 feet) - https://www.metalsupermarkets.com/pro...
Steel Pegboard 32" x 16" (#5105914) - https://www.lowes.com/pd/Kobalt-Steel...
Rockwool Mineral Wool 60 Acoustic Insulation 48"x24"x1" Case of 12 (roxulRB601X12) - https://www.acoustimac.com/roxul-rb6-...
SS Rivets 3/16" x 3/8" - https://amzn.to/4pn3zjS
SS Rivets 3/16" x 1/2" - https://amzn.to/42geeCQ
Smoker Gasket Seal - https://amzn.to/4mYNwak
Thermometer with Probes - https://amzn.to/45XdMvA
Flexible Latex Sealant - https://amzn.to/46131IN

========== Misc. Products ==========
91% Isopropyl Alcohol - https://amzn.to/414EgY8
Air/Hydraulic Riveter - https://www.harborfreight.com/14-in-a...
Black Nitrile Gloves - https://amzn.to/3TvBVjI
Cut-Off Tool - https://amzn.to/4m6RHiP
Cut-Off Wheels - https://www.harborfreight.com/3-in-x-...
Deburring Tool - https://amzn.to/46dvABt
Hole Saw Kit - https://amzn.to/4ntmrvK
Respirator - https://amzn.to/3MOE08f
Utility Knife - https://amzn.to/46gTImP

Tools:
1/4" Drill Bit
1/8" Drill Bit
3/16" Drill Bit
1.5" Hole Saw
91% Isopropyl Alcohol
Air/Hydraulic Riveter
Angle Grinder
Caulking Gun
Cut-Off Tool
Deburring Tool
Drill
Measuring Tape
Nitrile Gloves
Oscillating Tool
Phillips Screwdriver
Reciprocating Saw
Respirator
Rotary Tool
Safety Glasses
Shop Towels
Square
Utility Knife

Disclaimer: Content produced from Mcgurr Entertainment is for entertainment purposes only. This information is not endorsed by any agency/company (such as Ford) and is intended as an entertainment. Mcgurr Entertainment assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. All content on YouTube is provided in good faith, however we make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability or completeness of any information on YouTube. Use this information at your own risk.

#DIYOven #PowderCoat