Water Pump Replacement--Jeep Grand Cherokee 5.7L HEMI (2011)

Learn to how to replace your water pump, thermostat, and serpentine belt on a 5.7L HEMI engine at home with common hand tools.

How to remove your Jeep's splash guard:    • Jeep Grand Cherokee 5.7L Splash Guard...  

5.7L Serpentine Belt Diagram: https://www.jeepgarage.org/threads/wk...


Amazon Affiliate link(s):
Parts
Water pump: https://amzn.to/3TySjiX
Thermostat: https://amzn.to/3vNlFzH
Serpentine Belt: https://amzn.to/3TAmFSm

Tools
Spill-proof funnel: https://amzn.to/3TJbXsY
Pick: https://amzn.to/3g4N1hC
Flathead screwdriver: https://amzn.to/3TuD7n6
Pry Bar: https://amzn.to/3X0i6DO
3" extension: https://amzn.to/3UWumn6
16mm: https://amzn.to/3hHld3p
15mm: https://amzn.to/3tr5oQS
13mm: https://amzn.to/3hJwuQR
10mm: https://amzn.to/3hB7hI5
5/8: https://amzn.to/3Gg1SAv
15mm deep: https://amzn.to/3Ae5lvo
19mm deep: https://amzn.to/3E55bYI
6mm allen/hex: https://amzn.to/3EsCYwe
3/8 Ratchet: https://amzn.to/3trNVro
Pliers: https://amzn.to/3UTYvTR
1/4 Ratchet: https://amzn.to/3ts1jMf
10mm (1/4 drive): https://amzn.to/3UZAivD
13mm (1/4 drive): https://amzn.to/3USAbSr
Abrasive sponge: https://amzn.to/3UGtGSX

Supplies
Red Gasket Maker: https://amzn.to/3tvfL6o


Disclaimer:
I am not an expert, just an average Joe who enjoys DIY'ing. Learn, Save, DIY assumes no liability for property damage or injury incurred as a result of any of the info from this video. Use this information at your own risk. Due to factors beyond the control of Learn, Save, DIY, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Learn, Save, DIY.



-------------------------------------------- Chapters ----------------------------------
00:00 Introduction
00:10 Tools Needed
01:12 Getting Started
01:20 Drain Radiator
03:22 Remove Engine Cover
03:47 Remove Intake
05:00 Move the Upper Radiator Hose
05:29 Remove Serpentine Belt
07:06 Belt Diagram
07:13 Remove Thermostat
08:45 Remove Idler Pulley
09:07 Remove Tensioner
09:34 Remove Lower Radiator Hose
09:47 Remove Coolant Temp Sensor
11:14 Remove Bracket
11:57 Remove Coolant Tube
12:54 Organizing Water Pump Bolts
13:31 Removing Water Pump
19:06 Clean Mating Surface
19:30 Install Bleeder Screw on Water Pump
19:58 Install Water Pump
29:44 Install Thermostat
29:50 Install Mounting Bracket
30:20 Install Coolant Temp Sensor
31:33 Install Tensioner
32:53 Install Bottom Radiator Hose and Idler Pulley
34:05 Install Serpentine Belt
35:22 Install Top Radiator Hose & Thermostat Housing
36:00 Install Intake
37:23 Filling/Bleeding the System with Coolant