4Runner Limited To TRD pro Front Bumper Swap/Conversion

In this video I take you step by step through the process of converting the front end of your 5th gen 4runner limited to the TRD pro style front end.

Please share your experiences/suggestions in the comments section to help others. I'll try my best to answer any questions you may have as well

Make sure to replace the passenger side air deflector with part number below (not shown in vid)

Only attempt to paint your front bumper if you have previous experience spray bombing
You will need 1-2 cans of primer, 2 cans of matched base coat (from auto paint store), 2-3 cans of 2k clear coat.
www.Partify.com or a local auto-body shop is a good safe route to have your bumper painted

List of Parts Needed
Note: Some of these parts/clips were ordered from Rock Auto. As mentioned in the video, Rock Auto offers off brand parts/numbers when you enter Toyotas part numbers. Many of these off brand parts have built in clips/retainers. If you go the Toyota branded route you may require more clips to secure the grille and fog lamb bezels. I would recommend purchasing the bumper cover, fog light bezel, and grille and test fitting everything together before hand to see how many clips you require for your conversion. You will likely have extra clips as you can reuse a lot of the originals, but better too many than too little

If you have TSS (2020 or newer) you will need a special grille that accommodates the sensor. Contact Toyota for correct part number(s).

TRD Bumper Cover: 52119-35914 has
SR5 Bumper Cover: 52119-35918
90467-07201 Bumper Cover Clip x5
52116-35140 Bumper Cover Retainer x5
90467-05138 Bumper Cover Nut Left x2
90159-60215 Bumper Cover Screw Left/Right x2

52127-35100 Fog Lamp Bezel Right
52128-35080 Fog Lamp Bezel Left
75392-35220 Fog Lamp Bezel retainer Right x2 or DORMAN 963648
75392- 35220 Fog Lamp Bezel Retainer Left x2 OR DORMAN 963648

53112-35060 Lower Grille (If you have TSS sensor in your grille 2020 or newer you may require a grille that accommodates this. Contact your Toyota dealer for the correct part number.
53901-35250 Valance Panel (not necessary if you order SR5 bumper cover or cutting to fit winch bumper)
75392-35220 Valence Panel Retainer (not necessary if you order SR5 bumper cover or winch bumper)
52134-35070 Retaining Bracket, Left
52133-35060 Retaining Bracket, Right
52148-35120 Stopper, Right (optional, did not install mine)
52021-35140 Reinforcement/”Crash bar” (May substitute body armor winch bumper TR-19339 or c4 lo pro winch bumper)

53875-35150 Front Mudguard, Right (May cut existing mudguard to work)
53876 -35150 Front Mudguard, Left (May cut existing mudguard to work)
52161-20010 Mud Guard Clips x 6
90159-60603 Mud Guard Screws x6
90467-07211 Hood Beauty Clips x5 or DORMAN 963634
53293-35020 Deflector, Right (Passenger side must be replaced to fit new bumper)
53294-35020 Deflector, Left (Drivers side can be left on! So no need to purchase)

*52129-35030 Lower Cover skid plate
(May substitute TRD pro skid plate or aftermarket from Car trim home also Greenlane offroad makes a really nice affordable aluminum skid https://greenlaneoffroad.com/)
*90467-09227 Lower Cover Clip
(May substitute TRD pro skid plate and hardware - aftermarket skids come with hardware)
*90109-06330 Lower Cover Bolt
(May substitute TRD pro skid plate and hardware - aftermarket skids come with hardware)

Pz323-35020 Upper grille garnish (May use aftermarket “Toyota” “4Runner” grill/garnish from https://www.4runnerlifestyle.com/coll...) or Reuse your limited upper grille/garnish as seen in video to save $$