How to Setup Netgear Range Extender and Mywifiext.net Introduction?

In this, You will learn what is mywifiext.net and how you can set up your Netgear wifi range extender device using the mywifiext.net.

www.mywifiext.net is not your regular website. It is a local Web address used to set up your Netgear range extender. When Any user enters mywifiext.net in their respective web browser they are redirected to a page where they are asked to enter their Username and Password to log in.

Once successfully logged into the website then Netgear genie page open ups where users can change their settings as per user requirement and set up their Netgear extender devices, Update settings, Firmware update, and much more amazing benefits
Since mywifiext.net is not just like your regular website and is especially a local website for Netgear users to access and set up their devices so you must be connected with the Netgear device wirelessly or through an ethernet cable to access this site.

Here are a few steps to setup Your Extender:-

Step 1. Place the extender in the same room as the WiFi Router.
Step 2.Make sure you have a live internet connection coming from the main router. Also, make sure that the router is WPS capable.
Note: WPS does not support WEP security. Change the security of your main router to WPA2-PSK (AES) for optimal performance.
Step 3.Plug the extender into an electrical outlet and wait for the Power LED Image to become solid. If it does not turn ON, press the On/Off button on the side panel of the extender.
Step 4.Press and hold the WPS button for about 2 seconds on the side panel of the extender. The WPS LED Image will start to blink.
Within 2 minutes, press the WPS button on your router.
Step 5. The WPS LED Imageon the Extender should turn to solid green and the Router Link LED Image should also turn solid green to let you know that your extender is connected to your main network.
Step 6. Move the extender to your preferred location, but make sure it is in between the router and the wireless devices to get a good signal.
Please check the best position to place the Extender in your network setup KB article.
Step 7.You can now connect your wireless devices to the Extender’s new SSID. The extender’s wireless network name (SSID) changed to your existing WiFi network name with '_EXT' at the end. The password to be used will be the same WiFi password as the one on your main router.
Example:
Existing WiFi Network name (SSID): MyHomeNetwork
Step 8. New Extender WiFi Network name (SSID): MyHomeNetwork_EXT
Note: If your wireless devices have a WPS feature; just press the WPS button on the extender and within 2 minutes, press the WPS button on your wireless device to instantly connect them without typing the wireless password.
Learn how to setup your extender by reading our guided tutorial.

Also Watch Our Other Videos:-

How to Setup Netgear N300 Range Extender - Step By Step Guide
   • How to Setup Netgear N300 Range Exten...  

Extender Buying Guide - Don't Buy Extender Until You Watch This
   • Extender Buying Guide - Don't Buy Ext...  

How to Reset Netgear Range Extender | Mywifiext
   • How to Reset Netgear Range Extender |...  

How to Setup Netgear Range Extender? Mywifiext
   • How to Setup Netgear Range Extender? ...  

What is www.mywifiext.local? Explained.
   • What is www.mywifiext.local? Explained.  



DISCLAIMER: Please don't go out of your way to or hate on anyone I talk about in my videos, this channel is to educate people and I usually focus on education users through technology.

Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational, or personal use tips the balance in favor of fair use.

Thanks For Watching.