📌 𝐅𝐨𝐥𝐥𝐨𝐰 𝐨𝐧 𝐈𝐧𝐬𝐭𝐚𝐠𝐫𝐚𝐦:- / drgbhanuprakash
Identify and prepare the site
---------------------------------------------
Do a preliminary inspection (nonsterile) to identify a suitable vein: Apply a tourniquet, have the patient make a fist, and palpate using your index finger to locate a large-diameter vein that is nonmobile and has good turgor.
To help distend and locate veins, tap a potential site with your fingertips. It may help to allow the arm to hang down, increasing venous pressure. Use a vein-finder device if a suitable vein is not readily seen or palpated.
After identifying a suitable cannulation site, remove the tourniquet.
Apply anesthetic if it is being used and allow adequate time for it to take effect (eg, 1 to 2 minutes for gas injector, 30 minutes for topical).
Cleanse the skin site with antiseptic solution, beginning at the needle-insertion site and making several outwardly expanding circles.
Wait for the antiseptic solution to dry completely.
Obtain the blood sample
----------------------------------------
Try to access the vein efficiently and collect the blood sample within 30 seconds after tourniquet placement. Do not leave the tourniquet on for greater than 1 minute.
Reapply the tourniquet proximal to the selected insertion site. Do not have patients make a fist or let their arm hang down during the blood sampling, because these maneuvers may cause various erroneous laboratory values (eg, increased potassium, lactate, phosphate).
Palpate with your gloved finger to locate the middle of the target vein.
Apply gentle traction to the vein distally using the thumb of your nondominant hand to prevent the vein from moving. Traction may not be necessary for larger veins of the forearm or antecubital fossa.
Tell the patient that the needlestick is about to happen.
Insert the needle proximally (ie, in the direction of venous blood flow), with the bevel facing up, along the midline of the vein at a shallow angle (about 10 to 30 degrees) to the skin.
Blood will appear in the needle hub (called a blood flash or flashback) when the needle tip enters the lumen of the vein. Stop advancing the needle, lower the needle to better align it with the vein, and advance it into the vein an additional 1 to 4 mm, to ensure that it stays in position during blood collection.
If no flash appears in the hub after 1 to 2 cm of insertion, withdraw the needle slowly. If the needle had initially passed completely through the vein, a flash may now appear as you withdraw the needle tip back into the lumen. If a flash still does not appear, withdraw the needle almost to the skin surface, change direction, and try again to advance the needle into the vein.
If rapid local swelling occurs, blood is extravasating. Terminate the procedure: Remove the tourniquet and the needle and apply pressure to the puncture site with a gauze pad (a minute or 2 is usually adequate unless the patient has a coagulopathy).
Keep the needle motionless.
Begin to withdraw the blood sample and, when blood begins to flow, remove the tourniquet.
When using vacuum tubes, push each tube fully into the tube holder, use care to avoid dislodging the needle from the vein. Fill multiple collection tubes in the proper sequence. After removing a tube from the holder, gently invert the tube 6 to 8 times to mix the contents; do not shake the tubes.
When using a syringe, pull back on the plunger gently to avoid damaging the blood cells or collapsing the vein.
When blood collection is complete, gently hold a folded gauze square at the venipuncture site with your nondominant hand, and in one motion remove the needle and immediately apply pressure to the site with the gauze. Remove the tourniquet if you did not do so earlier.
Have the patient or an assistant continue to apply pressure to the site.
If you used a syringe to collect the blood, now transfer samples to collection tubes and bottles;* either insert the needle directly into the tops of the vacuum tubes, or remove the needle and attach a vacuum tube holder to the syringe. Do not inject blood into vacuum collection tubes; allow the vacuum to draw the blood into the tube. After blood has been added to a tube, gently invert the tube 6 to 8 times to mix the contents; do not shake the tubes.
Deploy safety cover over the exposed needle. Deposit used blood-collection devices (with needles) into a sharps container. Do not recap nonsafety needles prior to disposal unless a sharps container is not immediately available.
Dress the site with gauze and tape or a bandage.
#bloodsample #venipuncture #bloodtest #physiologypracticals #neetpg #usmle #usmlestep1 #clinicalessentials #clinicals
Информация по комментариям в разработке