Is this the cleanest 250k mile 3rd Gen 4Runner EVER?!

Leaving out a ton of new OEM maintenance parts here:

Axles:
• OEM Toyota eLocker rear axle, built by Rock Rash Performance in Fayetteville NC
o Nitro Gear 4.88 Ring and Pinion set
 all new OEM axle bearing/seal parts, including:
• New Wheel Bearings 3634-0020
• New bearing case housings 42421-35030
• All 8 new axle studs to housing (4 each side) 90114-10016 + 8 nuts 90179-10067
• Rear axle oil seals 9031050006
• Bearing retainer o-rings 9030188077
• New axle shaft snap rings 9052036045
• New ABS rotors/ tone rings 4351735010
• All 4 new axle bearing retainers 4242320010
• Rear diff plug, new 9034118006
• NEW Aisin SAT-008 E-locker actuator/motor/and wiring kit
• New elocker shaft retainer- 41469-60010
• New shaft retainer bolts 9010508214
• SlagFactory New Grade 10.9 stainless button-head studs for 3rd member, with nyloc washers
• New elocker position indicator switch- 84222-12010
• New Marlin Crawler 112mm elocker studs and hardware
• Marlin Crawler ¼” thick rear diff armor, full coverage
• EimKeith rear upper control arm reinforcements welded in
• 12Volt Guy standalone e-locker harness set up
• Nitro Gear 4.88’s in the front differential
o Detroit True-Trac 7.5” Limited slip differential
o East Coast Gear Supply clamshell bushings
o New OEM inner CV oil seals
o DuroBump front diff mount bushings
• Rear diff breather extended to fuel filler neck, using all OEM new breather, nipple, and high-quality aftermarket braided steel line.
• eLocker breather extended up into the cab through fuel tank area

Brakes:
• Tundra 199mm calipers, Centric e-Coated 2001 Tundra Rotors, and Akebono Pro-Act ceramic brake pads + all new Centric zinc-coated front brake hardware.
• Toytec extended length braided stainless steel rear brake line (Body to axle)
• New OEM Toyota rear axle hard lines (Driver 47326-35062) (Passenger 47325-35282)
• New OEM Advics WCT08 1” rear wheel cylinders
• New OEM Toyota rear brake shoe set, with new drum brake hardware kit
• StopTech (Centric 950.44014) Tacoma stainless braided brake lines with banjo fittings
• New Brembo rear brake drums
• Sonoran Steel rear parking brake cable bracket
• ABS on/off toggle switch

Suspension:
• New OEM Toyota lower ball joints
• ARP Stainless 180k psi 763-1003 Lower Ball Joint bolts
o ‘02 Spindles gusseted with Total Chaos Fab Gussets. Seam welded both sides.
o New OEM Koyo bearings
o New OEM bearing snap rings
o New OEM hub interface dust seal, and rear CV oil seals
o New 1st Gen Tacoma Hub assemblies with new 4-pin lock nuts
o ARP extended length wheel studs
o Marlin Crawler manual hub hardware- new. Cone washers, studs, etc
o NEW OEM Aisin FT-019 manual locking hub bodies and dial interfaces
o New lifetime warranty NAPA MaxDrive CV axles
• BTF Fabrication Uni-ball Upper Control Arms with Energy Suspension bushings
• OEM front lower control arms rebuilt with new Whiteline poly bushings, gusseted/reinforced with EimKeith materials
o double-shear shock lower mount.
• New OEM alignment cams, tabs and through-bolts (eccentric).
• Steering shaft spot welded for rigidity + tilt knuckle ball shimmed to make it tighter
• New OEM Toyota rack and pinion system, including new inner tie rods .
• New Polyurethane steering rack bushings
• New OEM Toyota outer tie rods
• New OEM Toyota high pressure steering lines and high pressure switch
• New OEM Toyota Intermediate Shaft
• Eibach Pro-Lift Front kit including: new front struts and shocks (coilovers)
• New KYB front spring Isolators and installation parts+ 2” extended length top hat studs.
• Bilstein 5160 rear remote reservoir shocks, with custom aluminum resi brackets.
• Metalcloak Jeep JK front 2.5” Dual rate coil springs installed in rear
• Sonoran Steel fully adjustable rear panhard bar
• EimKeith panhard correction brackets- corrects panhard angle from lifting
• EimKeith front strut tower top plate reinforcement, welded on.
• Camburg 8” front suspension limiting straps with KarTek adjustable clevis and shackles
• Durobumps front and rear bumpstops (5.25” rear)
• OptOffRoad adjustable rear upper control arms with Johnny Joints
• New OEM Toyota rear UCA bolts and nuts (x4 each)
• Total Chaos Fabrication 1” front differential drop kit to allow correct CV angle
• 01-02 Toyota Tundra 16”x7” OEM Steel Wheels powder coated
• BFGoodrich KM2 255/85/16 MT (Load Range E) tires all around
• Shrockworks 3/16” steel Radiator, Engine, Transmission, Transfer case and gas tank skid plates- Powdercoated black- Full set of everything they offer.
• Rokmen DOM tube rear lower control arms with poly bushings and new OEM Toyota hardware
• ARP Extended length Wheel Studs all around and Muteki 12x1.5 open-face lug nuts.
• RadRubber Designs engine splash guard set.
• AMP’d Up LLC bolt-on front winch plate with 10.9 graded hardware
• Factor 55 Hawse 1.5 fairlead
• Factor 55 flatlink e and rope guard
• CustomSplice 3ft synthetic winch rope sleeve
• Warn VR-10 EVO Synthetic line 10k Winch, wired or wireless capability