Kaabo Electric Scooter Troubleshooting Repair Methods of Error 02 | Kaabo official

#kaabo #electricscooter #kaaboerror

This video is for the customers who are facing the motor of scooters with Error 02. In this video, we will show you how to Troubleshoot or repair your kaabo Electric Scooter for Error 02.

Troubleshooting Process:
During the use of the scooter, the dashboard displays Error 02,
which is the Hall error of the motor. Press the M key on the switch, if 02 is displayed in the F area, it means that it is a problem with the front drive. Check if the Hall wire of the junction box is loose, if it is loose, plug it in tightly. If check that the Hall wire is not loose, but the dashboard still displays Error 02.
At this point, we need to swap the front and rear motors, and we need to close the dashboard first. Use diagonal pliers to cut the cable ties. Disconnect Hall wires and other wires Connect the front motor wire to the rear control, first link the Hall wire Phase lines linked by color. Unplug the power cord on the sub-controller. Wrap it with insulating tape to prevent short circuits. Unplug the main control connection ground wire.
At this time, there is still residual power in the sub-controller, and the positive and negative poles need to be contact to discharge. Use a 3mm Allen bit to unscrew the 2 screws below the junction box bracket. Use diagonal pliers to cut the tie. Lift the junction box bracket up slightly. Use a 4mm Allen bit to unscrew the four screws on the top and bottom of the junction box. Take off the front cover of the car and use a 3mm Allen bit to unscrew the four screws on it. After removing the original sub-controller, apply thermal grease to the back of the new sub-controller. Install the sub-controller into the controller box. Tighten the 4 screws on the front cover. Use a 4mm Allen bit to tighten the four screws.
on the top and bottom of the junction box. Use a 3mm Allen bit to fasten the two screws
below the junction box bracket. Connect the eight-core main wire terminal of the controller to the junction box. The main control is connected to the ground wire in series and wrapped with insulating tape.
Connect the Hall line first, connect the rest of the phase lines by color and wrap them with insulating tape. Next connect the power wire, first connect the black ground wire and wrap it with insulating tape. Next, connect the red power wire and wrap it with insulating tape. Finally, cover the controller compartment cover and tighten the four screws with a 3mm Allen bit.
Check if The Problem Is Solved. Open the dashboard, Error 02 is not displayed at this time indicating that the problem has been solved.

Are you Looking for a new way to get around town?🛴This E-scooter will reborn your life! Freedom is nothing but a chance to be better. Check out the kaabo best electric scooter.

Kaabo Others :
➡️Kaabo Wolf King Introduction:    • Wolf King GT Review | Official Promot...  
➡️Kaabo Mantis 8 Introduction:    • Kaabo Mantis 8 Introduction | Kaabo O...  
➡️Kaabo Mantis 10 Introduction:    • Kaabo Mantis 10 Unboxing and Assembly...  
➡️Kaabo Wolf Warrior 11 Introduction:    • Kaabo Wolf Warrior 11 In The Wild | K...  
➡️Kaabo Mantis 8 Unboxing:    • Kaabo Mantis 8 Unboxing and Assembly ...  
➡️Kaabo Mantis 8 City Riding Experience:    • Kaabo Mantis 8 City Riding Experience...  
➡️Kaabo Mantis 8, Mantis 10, and Wolf Warrior 11 Introduction:    • Kaabo Mantis 8, Mantis 10 and Wolf Wa...  
➡️Kaabo Wolf Warrior, Mantis, and Skywalker Introduction Video:    • Kaabo Wolf Warrior, Mantis And Skywal...  


BE OUR FRIEND ON:
➡️Website: www.kaabo.com
➡️Facebook:   / kaaboofficial  
➡️Facebook Group:   / 639170836988019  
➡️Facebook Group:   / 1066541750415033  
➡️Kaabo Instagram:   / kaabo_officialpage  

Thanks for Watching. Be with Kaabo Official.