Rc F1 Boat with Real Outboard Motor Mercury Racing 360 full 3d print

STL file https://cults3d.com/:2254330
####Mercury Racing 360 Outboard Engine###
-This outboard has a height of 20cm
-Suitable for hulls above 70cm, I will make many hulls that fit this outboard Engine! so you can make lots of rc boats with just one engine
-I used a 3670 motor, this outboard can use motors up to 4076 (not tested yet).
-this outboard can adjust trim position on mounting and and can be adjusted the height from hull
-gear lubricant hole for easier to fill the lubricant after playing
-easy to print without any support and pre orianted
-need 400grams of filament (pla) used abs for motor mounting
-have a great watercooling system

Print Setting:
-min print area = 200x140x50
-nozzle = 0.4
-layer hight = 0.15 lower is better for high quality
-perimater = 5 wall line
-top/bottom = 5
-infill = 30%
-support = no

BOM:
-bevel gear shaft 4mm 15t 0.8 2pcs ( https://a.aliexpress.com/_opczqfU )
-bearing 604zz 1 pcs ( https://a.aliexpress.com/_oCFW9Pv )
bearing 684zz 5pcs ( https://a.aliexpress.com/_oCFW9Pv )
shaft 4mm 30cm
rigid couple joint 4x5 (depending on the motor you use) ( https://a.aliexpress.com/_oDoRGWb )
-drive dog 4mm ( https://a.aliexpress.com/_okQpmtp )
-propeller up to 50mm (i use 40mm diamter) (https://a.aliexpress.com/_olAepaR )
-brushless motor up to 4076 ( i used 3670 2150kv)
heat insert m2.5 (2.5IDx3Lx3.5OD) 18pcs ( https://a.aliexpress.com/_olfvCxz )
m2.5x5 18 pcs ( https://a.aliexpress.com/_oEKdBSR )
-m3 x35/40 2pcs with nut (for adjustable trim position)
-m2x3 self taping screw (for gear lubricant hole)
-push rod connector 2pcs for servo rod ( https://a.aliexpress.com/_olInPFh )

####F1 Hull PowerBoat####
-70cm length
-Nice desain and performance
-easy to build and print withoutsupport
-have a pin joint for each body to make easier to put it together
-need 1.300gram of pla

Print Setting:
-Min print area = 235x235x230
-nozzle = 0.4
-layer hight = 0.2 lower is better for high quality
-perimater = 2/3 wall line
-top/bottom = 4
-infill = 15%
-support = only servo mount

BOM
-m3x8mm 16pcs for battrey tray, esc tray, servo mount, and servo
-m3x25mm 4pcs and nut 4pcs for outboard mount
-m3x40mm 3pcs and nut 3pcs for cover
-Push rod or stainless stell Leader Fishing wire for servo rod

Electronic that i used
-Battrey 2pcs lippo 2s 5000mah
-Esc Flycolor 150a
-Servo 25kg waterproof
-dumborg 6ch transmitter

3D PRINTING SETTINGS

3d printer fdm
-nozzle = 0.4
-layer hight = 0.2 lower is better for high quality
-perimater = 4 wall line
-top /bottom = 4
-infill = 30%
-support = no

#f1 #outboard #mercury #rcboat #diy #3dprinting #3dmodeling #f1h2o #rc #casting