Tiger cutting board. CNC Inlay. Maple cutting board inlaid with walnut. Wood Inlay. BroinwooD

Wood: maple, walnut, dark cherry.

How to find inlay parameters.
https://broinwood.com/products/how-i-...

Feed rate v bit 30ipm https://amzn.to/3wf9Txg 👍👍👍
Feed rate flat nose 1/8 40ipm https://amzn.to/3izKXcF 👍👍👍

For orders go to https://broinwood.com/pages/custom
Check out our Instagram page   / broinwood  
https://broinwood.com/
email: [email protected]

🔥🔥🔥Here some stuff which I use in my workshop and really love it.
Maybe it will be useful for you.🔥🔥🔥

Definitely recommend this Oil and Wax for cutting board:
https://amzn.to/36ytyi1
https://amzn.to/3nrAPGL

My glue:
https://amzn.to/3jyVMNu (really love it)

Double-Sided Duct Tape:👍👍👍
https://amzn.to/33ANxen (It holds blank well, but anyway, I also use screws.)

My Random Orbit Sanders I love how they work but they get a little dusty:
https://amzn.to/36u5mxs
https://amzn.to/3d1oNiv
Makita 3/4-Inch ID/1-OD diameter by 10-Foot Hose
https://amzn.to/33uGmnS

My Sanding Disc (for me they are the best!!!):
3M Cubitron II
https://amzn.to/2SrnAHs (80 and 120 grit)
https://amzn.to/2SqlvvH (150 grit)
https://amzn.to/3nksyUQ (220 grit)
https://amzn.to/2GriKaZ (320 grit)

My router bits which I use a lot:
My favorite router bit!!!:
Metric CNC 2D and 3D Carving 6.2 Deg Tapered Angle Ball Nose (clean cut, long life, definitely recommend) 👍👍👍
https://amzn.to/3wf9Txg

2D & 3D Carving 12.4 Deg Tapered Angle Ball Tip x 1/32 Dia x 1/64
https://amzn.to/3sviUAl (clean cut, long life, definitely recommend)

Standard Spiral Bit with Down Cut 1/8-Inch Cutting Diameter
https://amzn.to/3izKXcF

15 Degree v bit (be careful easy to break down)
https://amzn.to/3izLyLr

Round Nose Bit with 3/8-Inch Radius, 3/4-Inch Cutting Diameter and 1-1/4-Inch Cutting Length
https://amzn.to/2SsZYlV (I use it for juice groove)

1/2-Inch Dia. 2 Flute Ball Nose Spiral End Mill Router Bit
https://amzn.to/33v99Zm (I use it for juice groove)

Spiral Flush Trim Bit with Down Cut and 1/2-Inch Cutting Diameter
https://amzn.to/2SsB8m7

Three Flute with Spiral Bit 1/2-Inch Cutting Diameter and 2-Inch Cutting Length
https://amzn.to/2HTgwkV (I use it for flatining surface and makining cutting board shape)

Spiral Bit with Up Cut 1/4-Inch Cutting Diameter and 1-Inch Cutting Length
https://amzn.to/36u2Hns (I use it for cut off inlays. it doesn't make chips.)

My Collet Set:
https://amzn.to/33xbO4X

My DEWALT Plate Joiner:
https://amzn.to/33xtkWQ (it is not bad and not good it is ok)

My Bandsaw Blade it is inexpensive and cut well:
https://amzn.to/34uKNy8

Hi,
My name is Nik. Welcome to my channel!
I appreciate your likes and subscriptions!

Sincerely,
Nik.