Скачать или смотреть ALERT: Do fuelless generators work? Is self powered generator real? DIY to build fuelless generator

This is a test project to know if i can swiftly tap current from a 1.2kva generator hoping that it will continue to run itself.
method in this video is by using an orange knifeSwitch /switch box method, but it failed to continue to power the electric motor. I have tried four other methods too, all to no avail.
so I want to believe that without a constant rotating speed applied to the generator, you can not successful switch from outsourced current (external) to the generator's current (current supplied from the generator).

I noticed that the current supplied when i powered the motor to run the generator seemed to be constant and really bright, unfortunately i do no have a voltmeter to measure the voltage. but i can tell you that in my country our standard voltage supply is 220v.

The challenges I faced when i was tearing down the generator and during the test were:
I intentionally wanted to leave the cranshaft yo serve as a flywheel of the generator in it to help reduce feedbacks when the generator is in used provided the project was successful.
NOTE THAT I HAVE NEVER OPENED A GENERATOR BEFORE. lol

FIRST CHALLENGE:
1. Each time I came across a roadblock like a different kind of nut or bolt, I quickly went to buy it. lol.
I can tell you I went to tool store for more than 9 times to get a new tool.

2. Removing the cylinder and rod. I did not want any friction or resistance as the engine rotates so the carburettor and cylinder alongside its rod needed to be removed.
I was able to remove it with the help of a generator mechanic but the process altered the cranshaft bearing. So I abandoned the cranshaft as it could not spin well when i placed it back inside the generator.
the friction was a lot that it felt choked up.
To cut cost i went to a generator store to get another one. I took the new cranshaft to a welders workshop, but this time to cut off the arm of the rod of the cylinder. Wow that was what i should have done. so if you are doing this as well don't try to waste time removing the rod jointed to the shaft, just cut it off at the neck of the ring where it meets the flywheel cranshaft. mind you that was the 7th time I went out to get something done.
The new idea of cutting the cylinder at its ring neck worked so well when i replaced the cranshaft that's serving as my flywheel in the generator.

3. Deciding on the coupler to use in order to Eliminate Vibrations to its minimal.
I tried direct pipe joint, Rubber or hose joint with clips (dint last long), Universal joint (U-joint was not so good), propeller rubber joint using pieces of rubber gotten from used tyre. (YES very impressive result).

4. Deciding on the external compartment (building an extension for the generator) something to house the electric motor as it will as well be attached to the body of the generator.
But at the moment, i have pedalled down on that because I don't know if i will build a different design peradventure the whole project will result to a different approach entirely.
I am stock at the junction where the generator refused to continue to supply the motor to make it a self-powered or free Energy.

5. I don't have a voltmeter reader. I will buy that when i include on the solution to make it power itself.
please note that i want to still use the electric motor, i dont have extra money to buy a big flywheel, nor do I actually have much money to spend on this project, so i need a simple solution from your comments. please I am not a physics student kindly speak to me in a layman's terms.. lol

6. for the switch, i also tried a one tap switch. nothing happened.

7. I also replaced the cover of the generators coil sections because i over-screwed the nut, thus breaking the cover. The metal cast body is super fragile. I had to get another one. no room for excuse/error.

So after the project was 80% done, i decided to test it to see if I was on track. but i reached a roadblock. (the last stage of the video where the generator produced current and was about to switch the supply of the electric motor to consume from the generator).
I decided to reach out to YouTube if i can get help and i was surprised to see more videos but i believe there are some with false claims especially the ones with the electric motor and 1.2kva generator.

The videos that claims to remove the electric motor from external source to the current from the generator (especially small 1.2kva generators without a massive flywheel nor a second motor to sustain the rotation of the generator at maximum speed) are all false claims.
I want to believe that there is a secret modification somewhere that they did not reveal.

If I'll make use of a big flywheel it has to be for a 10kva alternator. But no funds right now. so Im sticking to making this one work without changing the electric motor.
please leave a comment, what do I need to do next.

so i decided to make a video and post.
please viewers
i need comments please, solutions.

help me bring this project to life. 😞😶