Скачать или смотреть How to build my CHEAP DIY Golf Simulator - Update (V2)

Written companion: https://www.chuck-builds.com/golf-sim...

After I accidentally broke my golf simulator, I decided to revisit the drawing board to brainstorm the biggest improvement with the least amount of additional cost. This ended up being a used projector (brighter), another net (seamless ball protection), and Unistrut (less wrinkles and sag). While it isn't a huge change from my version one, I tried to capture the whole build and thought process - even before I knew what I would end up with.

Most of the video is me building the screen but I talk about some specifics towards the end. As a reminder, my goals are to keep this Cheap, DIY, and improve incrementally. I am not trying to compete with big money kits but rather try to find a sweet spot on a cheap, very playable Golf Simulator! Feel like I missed something? I might've talked (too much) about it in my first video - found here:    • DIY Roll-Up Garage Golf Simulator  



Amazon Affiliate List:
Hillman 150006, 5/16 X 18-Inch, 100-Pack Coarse Thread Hex Nuts, 5/16"-18, Steel, 100 Pieces https://amzn.to/3TDrLjw
Small Parts 31WSAEPK Steel Flat Washer, Zinc Plated Finish, ASME B18.22.1, 5/16" Screw Size, 11/32" ID, 11/16" OD, 0.065" Thick (Pack of 100) https://amzn.to/3XA5oge
Coarse Hex Bolts, 5/16-18 x 3/4, Piece-100, zinc https://amzn.to/3MVllIN
Golf Net,10Ft x4 https://amzn.to/3BcFV51
Shock cord to tie net: https://amzn.to/4dqUMHJ
DURA-LIFT 1-1/8 in. x 24 in. Galvanized 14-Gauge Steel Punched Angle Iron Bracket & Mounting Hardware (4-Pack) https://amzn.to/3BcFZlh
3/8-16 x 6-Inch Threaded Rod, 5-Pack https://amzn.to/4djLNGW
Maker Pipe Threaded Pipe inserts 3/8"-16 : https://makerpipe.com/products/thread...


Top: Adamax 10-ft 12-Gauge Electro-galvanized Half Slot Channel Strut https://www.lowes.com/pd/Adamax-Adama...
Bottom: Adamax 10-ft 14-Gauge Electro-galvanized Half Slot Channel Strut https://www.lowes.com/pd/Adamax-Adama...
Steelworks 1-1/4-in W x 1-1/4-in H x 6-ft L Zinc-plated Steel Perforated-round Angle https://www.lowes.com/pd/Steelworks-1...

Golf Screen : https://amzn.to/3Qh1jdQ
JackShaft Garage Door Opener: https://amzn.to/3vYiH0d
Pillow Block Bearings: https://amzn.to/3Qk4cum
Pool Noodles to reduce bounce: https://amzn.to/4d9YEfZ
Hitting mat: https://amzn.to/44dcOZu
Foam mats to make Mat softer: https://amzn.to/3QgLXGl
Garmin R10: https://amzn.to/3AeEGC2
Callaway Ball Shagger: https://amzn.to/3xOjnWv

Projector Mount: https://amzn.to/4deN03c
Raspberry Pi 400 : https://amzn.to/40fmOld
HDMI to Ethernet : https://amzn.to/3JOcTJO


Tools I use:
Franklin Sensors ProSensor M210 Best Stud Finder with 13-Sensors, Wood & Metal Stud Detector/Wall Scanner, Live Wire Detection - https://amzn.to/3Yxf38P
Metal Tube Cutter - https://amzn.to/4bn5hKb

Timestamps:
00:00 - Introduction
00:15 - Timelapse
00:37 - Let's Build It
01:25 - Materials
03:35 - Cost Breakdown
03:45 - Step 1: Cut Angle Steel
04:17 - Step 2: Measure Twice!
04:44 - Measurements Are Hard
05:27 - Step 3: Hang Steel
05:52 - Step 4: Prepare the Pillowblock Bearings
07:20 - Hanging the Bearings (temporarily)
07:45 - Crossbar Plan
08:20 - Step 5: Cut EMT Conduit
08:25 - Step 6: Insert Threaded Inserts
08:55 - Use both Threaded Inserts
09:12 - Step 7: Insert Conduit into Unistrut
09:25 - Step 8: Insert Bolts to Unistrut to hold Screen
10:30 - Good View of how I am using the Bolts
11:22 - Step 9: Attaching the Screen
12:06 - Step 10: Relocate Bearings
13:23 - Step 11: Weight Screen with Half Channel Unistrut
14:14 - Step 12: Forget to film the rest of the video / Add Nets
16:15 - Back View of the Screen / How to Attach Nets
17:25 - Step 13: Moonlight & Remote Streaming the Simulation
18:25 - Garmin App Bug - Annoying!
19:45 - Projector Info
20:30 - Spotlight, Mats, and Ball Shagger
21:45 - Garmin R10
22:20 - Garmin Improved Readings with Reflections
23:05 - Flop Shot Net is Nice
23:30 - Outro & Driver Swing