How to Build RC Savage Bobber - Planeprint

Описание к видео How to Build RC Savage Bobber - Planeprint

This is full highly detailed build video of this 3d printed rc airplane. I will show how to setup all the electronics and how to assemble the entire airplane.

Thank you so much for watching!

If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmi...

See what else I am working on:
  / troymcmillan_rc  
  / troymcmillan_rc  

#3Dprinted,#RCairplane, #ItFlies

STL Files: https://www.planeprint.com/savage-bobber

How to Print Thin Wall:    • How to Print Thin Wall - Planeprint |...  

Big Bobber Videos
Assemble Part 1:    • How to Assemble 3D Printed Big Bobber...  
Assemble Part 2:    • How to get your Big Bobber ready for ...  
Full Maiden Flight:    • Big Bobber Maiden Flight - Planeprint  
Quick Full Build:    • 3D Printed Big Bobber Full Quick Buil...  


Products Mentioned:
Artillery Sidewinder 3D Printer: https://amzn.to/396eqIp​
Artillery Genius 3D Printer: https://amzn.to/39cA6CZ​
White PETG: https://amzn.to/2MvroIx​
Black TPU: https://amzn.to/2Sw3Oe8​
Orange PLA: https://amzn.to/3bBq13F
2204 Brushless Motor: https://amzn.to/2NTqsOt
20 amp ESC: https://amzn.to/37K2dcL
Emax Servo:
8x4.7prop: https://www.apcprop.com
CA Glue: https://amzn.to/2J8EvNW​
CA Accelerator: https://amzn.to/3fpbycz​
AR620 Receiver: https://amzn.to/3j4PbK4​
DX6 Transmitter: https://amzn.to/3l6NFsD​
3pin wire assortment: https://amzn.to/3l1xNYt​
XT60 connector: https://amzn.to/3iyZWnf​
Y-Harness: https://amzn.to/3jAFwvo​
Screw assortment: https://amzn.to/2SvMxSs​
2mm push rod ends: https://amzn.to/3nnjD4U​
Z-Bend pliers: https://amzn.to/34mA0rt​
Hot knife: https://amzn.to/34AGOB1​
Drill Bits: https://amzn.to/3nIJzrx​


*These are the settings I used for my Artillery Sidewinder 3D Printer for. surface layer 3. These settings are not going to work with every printer, or every PLA. Printers have different length bodin tubes, and PLA’s have different melting points. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck!

Profile 3 Cura Settings:
Quality:
Layer Height – 0.25
Line Width – 0.4
Shell:
Wall Line Count – 1
Infill:
Infill Density – 0
Material:
Printing Temperature – 215
Build Plate Temperature – 60
Flow – 100
Enable Retraction – Checked
Retraction Distance – 1.3
Retraction Speed – 10
Retraction Extra Prime Amount – 0.3
Speed:
Print Speed – 100
Outer Wall Speed – 35
Inner Wall Speed – 35
Travel Speed – 80
Travel:
Combing Mode – off
Cooling:
Enable Print Cooling – Checked
Fan Speed – 50
Mesh Fixes:
Union Overlapping Volumes – NOT Checked
Special Modes:
Surface Mode – Surface
Experimental:
Slicing Tolerance – Middle







Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!

Комментарии

Информация по комментариям в разработке