TP4056 и BMS 1S Что это такое Рабочий лист данных Схема микросхемы TP4056

@radal05
specifications, data sheets, functions and how it works tp4056 tp4056 type c tp4056 protection spesifikasi modul tp4056 tp4056 2a fungsi modul tp4056 tp4056 ic tp4056 output voltage
TP4056 dan BMS 1S Apa itu Cara kerja Datasheet TP4056 IC schematic
Link pembelian :
1.TP4056 with protection
https://tokopedia.link/OAW56B5nDwb
https://shp.ee/p9mtkvk
2. Bms 1s:
https://shp.ee/zkqpt2k

TP4056 schematic TP4056 IC TP4056 indicator TP4056 Circuit TP4056 Datasheet TP4056 pdf Cara kerja step by step modul TP4056 charger lithium
TP4056 dan BMS 1S Apa itu Cara kerja Datasheet TP4056 IC schematic
Data Sheet TP4056 :
https://www.addicore.com/TP4056-Charg...

Protection Features
This module uses the TP4056 / TC4056 Li-Ion charge controller IC and a separate protection IC. There are other types of modules on the market that use the TP4056 / TC4056 but lack any protection circuits or ICs to provide the necessary protection needed with lithium batteries. This module uses both the TP4056 / TC4056 and the DW01A Li-Ion battery protection IC, which together in combination provide the following protection features:
Manage the constant current to constant voltage charging of a connected lithium battery
Over-discharge protection - keeps your battery from being discharged below 2.4V, a healthy minimum voltage level for your battery
If a connected battery has been discharged below 2.4V the module will cut output power from the battery until the battery voltage has been re-charged above 3.0V (the over-discharge release voltage), which at that time the module will again allow discharge of power from the battery to a connected load. Although the module cuts output power from the battery during an over-discharge situation, it still allows charging of the battery to occur through the parasitic diode of the discharge control MOSFET (FS8205A Dual MOSFET).
TP4056 dan BMS 1S Apa itu Cara kerja Datasheet TP4056 IC schematic
Overcharge protection - the module will safely charge your battery to 4.2V
Overcurrent and short-circuit protection - the module will cut the output from the battery if the discharge rate exceeds 3A or if a short-circuit condition occurs
Soft-start protection limits inrush current
Trickle charge (battery reconditioning) - if the voltage level of the connected battery is less than 2.9V, the module will use a trickle charge current of 130mA until the battery voltage reaches 2.9V, at which point the charge current will be linearly increased to the configured charge current.
Can be powered, for charging, from a USB cable (USB Micro or USB C) or the + and - connections, see Power Supply Options Diagram below. The power source needs to be able to provide at least 1A for the charger to correctly charge a connected battery. Most modern phone/USB chargers can provide 1A or more; refer to the label on your phone charger to verify. If you use a USB cable, make sure that it is made to carry at least 1A.
Includes two indicator LEDs. Red LED indicates charging. Blue LED indicates charge complete.
The charge current can be configured externally with the Rprog resistor (R3, see below diagram). The datasheet for the TP4056 (refer to link in resources section below) includes a table and equation for what resistor values to use for configuring different charge currents.
The module uses a very small amount of current (in the micro amps) whenever it is connected to a battery. It is fine to leave it connected to a battery for long periods, but if you plan to not charge the battery within four months then we recommend disconnecting the module from the battery.


TP4056 dan BMS 1S Apa itu Cara kerja Datasheet TP4056 IC schematic
SPECIFICATIONS:
Charge Controller TP4056 / TC4056
Protection IC DW01A
Charge/Discharge Control MOSFET FS8205A
Charge Method Constant-Current/Constant-Voltage (CC/CV)
Input Supply Voltage 4.5~6.0 V
Constant Charge Current 1 A
Configurable with Rprog resistor (R3, see diagrams and TP4056 / TC4056 datasheet)
Charge Complete (Float) Voltage 4.2 V ±1.5%
Overcharge Protection
Overcharge Detection Voltage 4.3 V ±50 mV
Overcharge Release Voltage 4.1 V ±50 mV
Over-Discharge Protection
Over-Discharge Detection Voltage 2.4 V ±100 mV
Over-Discharge Release Voltage 3.0 V ±100 mV
Overcurrent Protection
Overcurrent Protection Threshold 3 A
Overcurrent Cutout Delay 10~20 ms
Short-Circuit Cutout Delay 5~50 µs
Trickle Charge (Battery Reconditioning)
Trickle Charge Threshold Voltage 2.9 V ±0.1 V
Trickle Charge Current 130 mA ±10 mA

00:00 Radal05
00:12 Modul TP4056
01:10 Apa bedanya dengan BMS 1S
01:35 Skematik tp4056
02:04 Bagaimana arus mengalir
03:05 Kemampuan BMS 1S
03:36 Skematik BMS 1S
04:50 Arah arus Charger pada BMS 1S
07:31 Arah arus saat Discharger
10:00 Cara menentukan besar arus mengalir
12:00 Kesimpulan

TP4056 dan BMS 1S Apa itu Cara kerja Datasheet TP4056 IC schematic