How-To: Exhaust Removal & Install // Chevrolet Camaro 6th Gen // 2016-2024

How-To: Exhaust Removal & Install // Chevrolet Camaro 6th Gen // 2016-2024

This video will cover how to remove the factory OEM exhaust from the LT1 or LT4 V8, and install an aftermarket exhaust of your choice. In this video, we install a Corsa Xtreme+ cat-back system onto Matt's 2023 Camaro ZL1.

Thanks to ‪@mike_budny‬ for the music! Check out Unwritten Verses, coming soon to all the major platforms!

Affiliate Links:
Skip-shift Eliminator for TR-6060 Manual Transmission:
https://amzn.to/3MwnR9y

LED Side Markers:
https://amzn.to/42RBzJ2

Lift Pads:
https://amzn.to/3s3FwtT

ZL1 Addons Premium Magpuck:
https://amzn.to/3KxA5MZ

Rotofab CAI for Camaro w/ LT4 V8:
https://amzn.to/43jSmW8

Rotofab CAI for Camaro w/ LT1 V8:
https://amzn.to/3ZRchbT

Corsa Extreme Axle Back Camaro V8:
https://amzn.to/3BSxdG3

Corsa Carbon Fiber CAI for ZL1:
https://tinyurl.com/wr8s4rx8

Adam’s Polishes Rolling Seat:
https://amzn.to/3OsxvdV

Bestool 4-Ton Jack Stand:
https://amzn.to/3nYDiNO

Esco 3-ton Jack Stand // Standard:
https://amzn.to/3pJlKmT

Esco 3-ton Jack Stand // Standard - 4-Pack:
https://amzn.to/42qDzch

Esco 3-ton Jack Stand // Low Profile:
https://amzn.to/3JxviZY

22mm Wheel Socket:
https://amzn.to/3x7Pzzq

22mm Extended Wheel Socket:
https://amzn.to/3qW8UCD

PB Blaster Penetrating Oil:
https://amzn.to/3q67ojc

Lisle Exhaust Hanger Removal Tool:
https://amzn.to/3pW70n9

7/8” / 22mm O2 Sensor Socket:
https://amzn.to/3osUWJO

7/8” Combination Wrench:
https://amzn.to/41ZTM6d

1/2" Combination Wrench:
https://amzn.to/3b8aFDM

Milwaukee 1/2” Drive Socket & Wrench Set:
https://amzn.to/430BKlz

Milwaukee 3/8” & 1/4” Drive Socket & Wrench Set:
https://amzn.to/3Mztv98

11mm Combination Wrench:
https://amzn.to/3Gm0muf

11mm Line Wrench:
https://amzn.to/3BeTJWI

Compact LED Flashlight:
https://amzn.to/2XPLWRO

Silicone License Plate Frames:
https://amzn.to/3BMnoH5

Purple Panda Lavaliere Microphone:
https://amzn.to/3Behn5Y

Chapters:
0:00 - Intro // Overview
0:45 - Lifting the car
0:55 - Tools Needed
2:12 - Under the car // removing the crossmember bracket
3:35 - Location of the factory flange, slip clamp, and O2 Sensors
4:14 - Removal of O2 Sensor (DO NOT Remove Driver Side)
5:12 - Removal Removal of clamp bolt // Exhaust flange nuts
6:44 - Lubricating the hangers
7:23 - Removing the suitcase/exhaust tip hangars behind the rear bumper
9:33 - Removing the exhaust from the hangers
10:50 - Loosen and remove factory exhaust
12:00 - OEM exhaust outside
12:20 - Slip clamp is welded on and factory robots suck
13:00 - Connecting the Corsa exhaust link pipes on
14:22 - Connecting the Corsa X-pipe
15:02 - Connecting the muffler pipes and mufflers
15:55 - Corsa exhaust tips installed // Everything lined up & tightened // Center bracket back on
16:30 - Cold start on Corsa with revs
17:47 - Exterior shot // Before & after audio
19:50 - Outro // Heard from a distance

These are affiliate links to the products. I make a small commission on anything purchased from my links.

**Disclaimer:
Due to factors beyond my control, I cannot guarantee against improper use of the information I share in my videos. (FollowMyLine17) assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not (FollowMyLine17) or any business affiliated to (FollowMyLine17).**