✨ GE DISHWASHER - NO POWER - Easy FIX ✨

✨ GE DISHWASHER - NO POWER - Easy FIX ✨
Fixed With A New Power Board
GET THE NEW POWER BOARD HERE: https://amzn.to/3a893cH
Easy to Install a new GE power board. It lives below the dishwasher door.
Before replacing the power board, try unplugging the wires to the power board for 30 minutes and then plug back in to see if it powers back up.
This is very common for GE Dishwashers.

✨Try these RESET instructions before replacing parts:

Discovering your GE dishwasher seems to have no power or is flashing and beeping for no apparent reason can be an unwelcome surprise or frustration that might have you thinking you need to call a dishwasher repair technician. However, there’s no need to fret, as chances are the issue can be resolved by performing a dishwasher reset.

How you reset your specific GE dishwasher will depend on its model number and whether it has the control panel on the front or on the top of the door.
What causes the dishwasher to need resetting?
There are several reasons why your dishwasher may need a reset. The more common reasons are a power surge, pressing the start button too many times, a failing component, or an aging control board.

If the dishwasher has been working without any issues or error codes showing, it is unlikely a more serious issue, like a failing component or defective control board, is responsible.

Power surge or power cut
If there is a power surge or power cut, most GE dishwashers will need to be reset. Reset instructions will vary depending on the model and type of GE dishwasher. However, in some cases, pressing the Start/Reset button and then waiting a few minutes will get the dishwasher to reset and reboot.

For other models, after a power failure the dishwasher Start/Reset button may blink when the power is restored. Pressing the Start/Reset button once should start the drain pump to remove residual water from the dishwasher. After about a minute, the dishwasher should be back to normal and ready to be used.

If the power went out while the dishwasher was in the middle of a cycle, with most GE models, the dishwasher will remember where it was in the cycle and resume from that point.

, the Start/Reset button, when pressed once, will start the dishwasher cycle. However, if pressed twice, the dishwasher will reset. Pressing the Start/Reset button will restart the cycle.

Beeping or blinking lights
Press the Start/Reset button
If the lights are blinking and the dishwasher is beeping, it can be as simple as pressing the Start/Reset button to return the dishwasher to normal. The issue could also be caused by the door being open, where closing the door properly resolves the issue. If the issue remains, disconnecting the power will likely solve the problem.

Disconnect the power
Beeping or blinking lights are often caused by a power surge or an error code.

One way to reset the dishwasher when the lights are blinking or the dishwasher is beeping is to disconnect the power to the dishwasher for 30 seconds. If the dishwasher does not appear to be reset, try leaving it unplugged for ten minutes instead. If your dishwasher does not have a plug, the power can be disconnected from your home’s electrical panel.

Blinking Start or Start/Reset button
If the Start or Start/Reset button is blinking, the dishwasher is likely shutting down after being reset. The light should continue blinking for 75-90 seconds before turning off. Once the dishwasher turns off, you can press Start to turn it on, and the dishwasher should be reset and ready to go.

Kickplate reset button
Some GE models have a reset button behind the kickplate access panel. If your GE model has a kickplate, you can unthread the screws to remove the access panel, and you may find two buttons in the bottom left corner. Pressing the first button will reset your GE dishwasher.

Make sure to disconnect the power before removing the access panel, as the junction box wires may be exposed, which could electrocute you, especially if you are unfamiliar with what is behind the kickplate.

To put the dishwasher in service mode, hold the Select Cycle button and the Start button down for five seconds. Next, to reset the dishwasher, press the Select Cycle button for five seconds. This should activate the lock button light. Press Select Cycle again for five seconds. Hold the Start button now for five seconds. The Start button should start flashing. Finally, hold the Start and Select Cycle button down for five seconds. The dishwasher control panel should now light up, and the dishwasher should be ready to go.

DISCLAIMER: This video or description may contain Amazon affiliate links, which means that if you click on one of the product links and buy the product, I’ll receive a small commission. Thank you for supporting this channel.

Scott The Fix-It Guy I’d Like To Thank All The Awesome Viewers That Have Supported This Channel By Subscribing or Joining as a Channel Member.
Thank You for Your Very Meaningful Support😊🙏