Replace the CV Axle and Wheel Hub Fast and Easy on a 2002 Monte Carlo SS

This 2002 Monte Carlo was experiencing some front end vibration over 55 mph and some unusual tire wear on the left front as well as some clatter from the CV’s as I turn it into a parking spot. I’m going to fix that with a new pair of CV axles and a new wheel bearing and hub assembly. This is not a very difficult job, but it does call for a few unique tools like a 35 mm socket and a torque wrench capable of 120 ft-lbs. Otherwise, this is something that can easily be done in your garage.

Here’s a link to a 35 mm socket: https://amzn.to/3xzeQUn
Need a torque wrench? Look at this one: https://amzn.to/3I8h7uC

The best place to start is to loosen the axle nut while the car is still on the ground. Then jack it up and stabilize it with jack stands. Next, take the wheel off, and begin by removing the caliper and caliper mount. With the rotor off, now is a good time to dislodge the CV from the hub. With a hammer, hit the end of the axle to force it inwards. Next remove the 2 bolts that hold the knuckle or spindle to the strut, these are likely going to need a hammer to remove. After that the knuckle can tilt away and the CV can be removed. Apply some prying force to remove the CV from the transmission. Sometimes a few smacks with a hammer can help if you can get a pry bar on it. That usually works better on the passenger side, the drivers side does not have the same clearance and you may have to use a pry bar without the help of a hammer.

With the CV out of the way, I replaced the hub too. It has 3 bolts and wiring for the ABS sensor. Once those are undone, it’s a matter of swap the parts with the new ones and reverse disassembly.

Once everything is back together, torque the axle nut. I torqued mine to 120 ft-lbs. Test drive the car to make sure that everything is in good shape and double check the torque after the test drive.

This is not a hard project and can easily be handled in an afternoon.

Here’s more parts for this job
CV axle: https://amzn.to/3xDerjY
Wheel bearing and hub: https://amzn.to/3lNWZ9I

Here’s some links to stuff I like to use!
PWRCORE 12 Brushless 12V Drill Driver & Impact Driver- https://imp.i284638.net/EarjvD
PWRCORE 12 Brushless 12V 3/8'' Impact Wrench Kit - https://imp.i284638.net/qn54Aq
PWRCORE 12 12V Mechanical Light Bare Tool - https://imp.i284638.net/a1vn5q
Kimo Electric Ratchet - https://amzn.to/3XQLpYO
WavWatch - Use Code ERIC100 for $100 off at checkout - https://www.wavwatch.com
Topdon Jump Packs - Use code SNOW10 for 10% off at checkout through my link - https://topdonusa.com/collections/pow...

Please check out my partners and affiliates!

These are affiliate links and I may receive a small commission at no additional cost to you.

Racesponsorshipscourse.net- use code ERICSNOW10 for 10% off the Race Sponsorship Bootcamp

WavWatch.com - Use Code ERIC100 for $100 off of Frequency Therapy to better your life!

Sweetbathandbody.com - fine artisan soaps including the amazing Scrubbie Bar for greasy working hands

Topdon Jump Packs - Great easy to use tools to keep you up and running! https://topdonusa.com/collections/pow...

Greezyz Gurage - Liquid Pumice soap and skin care products https://greezyzgurage.com/collections... Family Racing

Division 7 Real Estate - https://www.division7realestate.com - your northern Utah real estate connection

Master Muffler of Clearfield, Utah - https://m.facebook.com/profile.php?id... use code Snow Racing for 10% off your service

ContingencyConnection.com - supporting grassroots motorsports

RMSTATOR.com - ATV, SXS, Motorcycle and Snowmobile Electronics

Velocity Racing Carbs -   / velocity-racing-carbs-200655040514674   amazing Carburetors built for your needs

Are you considering starting a YouTube channel? I highly recommend VidIQ to help you make the most of YouTube: https://vidiq.com/EricSnow