iPhone SE Teardown and Reassemble - Fixez.com

iPhone SE LCD & Screen:
Black: http://bit.ly/2ExoR8b
White: http://bit.ly/2ntlB6t
iPhone SE Battery: http://bit.ly/2FB1VnP
iPhone SE Repair Parts: http://bit.ly/2nxwzqI

https://www.fixez.com presents the official iPhone SE Teardown and Reassemble Guide. This HD video will show you how to completely take apart and reassemble your iPhone SE smartphone. Visit Fixez.com for all of the DIY iPhone SE replacement screens, parts, and tools you need to fix your cell phone quickly, and affordably.

If you need your iPhone SE repaired ASAP instead- we have you covered there too. Contact one of our skilled technicians at 866-233-6460 or [email protected] and they will fix your Apple device for you. They are available Monday – Friday, 9am to 5pm PST.

Subscribe to our YouTube Channel for additional DIY smartphone and tablet teardown and repair videos!    / @fixez  
Like us on Facebook:   / fixez.com  
Follow us on Twitter:   / fixezdotcom  

iPhone SE Teardown and Reassemble Guide Video Transcription:

Warning:

You are performing this repair at your own risk
We claim no responsibility for any damages that might occur

Find the premium tools used during this DIY repair here: https://www.fixez.com/categories/repa...

Step 1
Power down your Apple iPhone SE smartphone.

Step 2
Remove the two bottom 3.4 mm Pentalobe screws located next to the lightning connector.

Step 3
Place a suction cup near the home button.

While applying firm, constant force, use the plastic triangle opening tool to work around the display assembly and separate it from the iPhone SE rear case.

Just like the iPhone 5s, lurking beneath the iPhone SE display is the touch ID cable. Do not pull the display up too far without first removing the bracket and disconnecting the cable.

The display assembly is still connected to the iPhone by several cables, so don’t try to remove it entirely just yet.

Step 4
Remove the following 4 Phillips screws securing the metal bracket to the motherboard. These screws are different sizes, so be sure to remember where they go.

Use the fine tip curved tweezers to remove the metal bracket and disconnect the LCD, digitizer, and front camera and proximity sensor cables.

Step 5
Remove the following 3 Phillips screws securing the home button cable and the metal bracket in place.

Remove the metal bracket and then with the tweezers peel the iPhone SE home button away from the display assembly.

Step 6
Remove the following 7 Phillips screws.

With the tweezers remove the metal clip and then the iPhone SE earpiece speaker.

Step 7
Gently pry the front camera and proximity sensor ribbon cable away from the display assembly.

Now, separate the iPhone SE front-facing camera and proximity sensor cable from the LCD shield plate.

Step 8
Remove the following 2 Phillips screws and then the metal bracket.

With the spudger, detach the iPhone SE 3.8-volt battery from the logic board.

Use the fine tip curved tweezers to peel up the adhesive tabs at the bottom of the battery.

Grab the tabs and try to keep the adhesive flat and wide.

Slowly pull the adhesive away from the iPhone SE. The adhesive will stretch to many times the length of the battery, keep pulling until they come out from between the battery and the iPhone’s rear case.

Remove the iPhone SE battery.

Step 9
Detach the signal cable and then the iPhone SE lightning port and headphone jack assembly cable from the logic board.

Remove the following 7 Phillips screws and then the small bracket.

The iPhone SE loudspeaker assembly is now free and can be taken out.

Step 10
With a little spudgering the lightning connector and headphone jack assembly can be removed from the iPhone SE.

Step 11
Use the tweezers to remove the piece of tape and then detach the rear-facing camera from the iPhone SE logic board.

The 12-megapixel iPhone SE rear-facing camera can now be removed.

Step 12
With the tweezers detach the iPhone SE power and volume buttons ribbon cable.

Use the flathead screwdriver to remove the following 4 screws.

Now, remove the following 4 Phillips screws.

Carefully lift the iPhone’s logic board up and detach the Bluetooth and Wi-Fi antenna connector before removing it from the iPhone SE.

Step 13
Remove the following 5 Phillips screws and then the metal bracket over the vibrator.

Remove the following Phillips screw and then with the tweezers take out the vibrator.

Step 14
Remove the following 2 Phillips screws and then the metal bracket.

Now, remove the last Phillips screw.

Use a combination of the spudger and tweezers to remove the iPhone SE power and volume buttons cable. The cable also includes a contact for grounding.

With the cable out of the way you can remove the physical power and lock button, volume buttons and the vibrate switch.

Step 15
Carefully use the tweezers and spudger to remove the iPhone SE Bluetooth and Wi-Fi antenna from the rear case.