How To Step by Step AC Compressor Front Seal Replacement/Reseal/Shaft Seal

Repair / Rebuild kompressor wira DENSO / Lip's shaft seal. - https://bit.ly/3zK5V2y
How to Properly Recharge Your AC System / Cara isi gas Aircond kereta - https://www.shorturl.at/bdiqO

0:00:00​ - Intro
0:00:09 - Disclaimer
0:00:26​ - Compressor model DENSO 10PA15C
0:00:36 - Compressor has a leakage problem
0:00:47 - Damage O-Ring / Shaft Seal / Lip's seal
0:00:55 - Sign the compressor shaft seal failure
0:00:59 - oil under the car's hood
0:01:20 - some oil on the compressor pulley and around the compressor head
0:01:47 - Lip sealed / Shaft seal Denso 10PA15C
0:01:55 - Shaft Seal Protector Installer / Remover
0:02:07 - 1 Set O-Ring Compressor
0:02:10 - ND8 Compressor Oil
0:02:15 - 6 mm Hex Socket
0:02:19 - 10 mm socket
0:02:23 - Snap Ring Pliers
0:02:28 - Lots of Rags or Paper Towels
0:02:40 - Torque Wrench
0:02:42 - Phillips Screwdriver
0:02:46 - Flat Screwdriver
0:02:48 - Compressor Schematic Denso 10PA15 C
0:03:06 - Removing the Clutch Assembly
0:03:15 - Pulls off the Drive Plate
0:03:26 - Remove Pulley Circlip it using a Snap Ring Pliers
0:03:36 - Take Off the Pulley
0:03:36 - Remove the Ground Wire
0:04:05 - Remove the Magnetic Coil Circlip
0:04:08 - Pull the Coil off
0:04:20 - Remove the five Compressor Head Bolts
0:05:20 - Prying the front section of the Compressor
0:05:29 - The Cause AC Leaks
0:05:20 - Remove Snap Ring that hold the lip seal in place
0:06:02 - Push down the Lips Shaft Seal using
0:06:14 - Damage Lips Seal / Split into 2 pieces
0:06:25 - Clean the Shaft Housing from the older Lips Seal Carbon
0:06:33 - Remove the two-indexing pin
0:06:37 - Separate the Compressor sections
0:06:38 - Clean all the part off the Compressor
0:07:10 - Separate the middle sections of the Compressor
0:07:54 - Clean all the component and put back as before
0:08:12 - Coat the new o-ring install it
0:08:17 - Put back the middle section of the Compressor
0:08:23 - Lubricate the Compressor with some oil
0:08:51 - Position the two-guide pin on the Compressor
0:09:01 - Install the front suction valve, matches it with the pins
0:09:25 - Lubricate the Lip Shaft Seal
0:09:37 - Gently push the Lips Shaft Seal using 21mm socket
0:09:53 - Install flat surface Retainer facing the Carbon Seal
0:10:20 - Place the shaft seal protector over the shaft
0:10:38 - Shaft Seal Protector Installer keep the Seals in perfect condition
0:10:58 - Coat the new Shaft Seal and the Shaft Seal Protector
0:11:07 - Push down the compressor head with the new Seal in it
0:11:22 - Turn the Compressor upside down
0:11:33 - Remove the rear cover and change with the new O-Ring
0:13:09 - Insert the five through bolts
0:13:13 - Tightened the bolts with a star pattern
0:13:27 - Torque the bolt to 21Nm
0:14:10 - DENSO 10PA15C uses ND-8 oil - quantity 120 cubic centimeters
0:14:34 - Put in Compressor oil, rotate the Compressor
0:15:08 - Check the Compressor, sealed correctly??..
0:15:35 - Last O-Ring, on the top of the Compressor
0:16:03 - Reattach four screw bolts, torque it to 21 newton meters
0:16:53 - Put the Clutch Coil onto the Compressor
0:17:17 - Put the flat side snap ring facing the Magnetic Coil
0:18:46 - Congratulations, you have just rebuilt your AC Compressor

Dalam video ini, saya akan berkongsi dengan anda semua. Cara untuk rebuild semula kompressor air cond kereta. Kompressor ini ada masaalah leaking. Dan saya rasa, masanya sudah sampai untuk saya overhoul kompressor ini. Model bagi kompressor ini DENSI 10PA15C.

ITEM USED
https://invol.co/claxngf - AC Denso Compressor Shaft Lip Oring Seal Kit
https://invol.co/claxnhq - 10PA repair O-Ring Kit
https://invol.co/claxnir - ND-8 compressor oil
https://invol.co/claxo0l - Hex Shank Impact Socket 6mm
https://invol.co/claxo1b - F rod Breaker
https://invol.co/claxo1x - DEEP SOCKET 10mm
https://invol.co/claxo2m - Torque Wrench
https://invol.co/claxo33 - Flat Screwdriver
https://invol.co/claxo3u - Philips Screwdriver
https://invol.co/claxo44 - Long Nose Pliers
https://invol.co/claxo4n - Snap Ring Pliers
https://invol.co/claxoc3 - Impact Wrench Cordless
https://invol.co/claxodr - RATCHET WRENCH

In this video, I will share with you guys. On how to rebuild a compressor. It might help others who are thinking of fixing their compressor. This compressor has a leakage problem. You will notice the face of the compressor is damp with lots of oil. The model for this compressor is the DENSO 10PA15C. The process for replacing the compressor itself is fairly simple. However, replacing it alone is not advised. I would suggest a full replacement of all o-rings in the system (since there may be leaks). As you remove them, take note (or take photographs) of the arrangement of spacers for each bolt, as they must be put back in the same locations. You also need to change it with new compressor oil.

#rebuild
#compressor
#denso
#Denso10PA
#reseal
#Nippondenso
#leaks
#refrigerant
#shaft
#sealed
#gasket