RC Hot Wheels car. 1/64 RC car. Paul Walker's Skyline from Fast and the Furious

Hot Wheels Nissan Skyline R34

Please visit my website for parts and files. https://www.slickdiecast.com

Please consider subscribing and turning on the notification bell.
https://www.youtube.com/c/SlickDiecas...


Follow me on socials.

Email [email protected]
Facebook   / slick-diecast-101889108462966  
Instagram   / slickdiecast  
Twitter   / slickdiecast  


Any donation will go towards parts so I can keep building for the community.
http://paypal.me/slickdiecast

Amazon shop: www.amazon.com/shop/slickdiecast

These are affiliated links. It helps the channel if you buy the parts using the links below.

Parts:
Rx43 micro receiver - http://microflierradio.com/Receivers....
_______eBay_______
70 mah micro LiPo battery - https://ebay.to/2Qc4C6U
1.7g rotating servo - https://ebay.to/3pyRzfW
N10 Dual shaft motor - https://ebay.to/3iZRoGs
On/Off switch - https://ebay.to/34pAL2O
SMD LED 0402 - https://ebay.to/3hidNhJ
2 pin connector - https://ebay.to/2Q7D56m
M1 screws - https://ebay.to/2YkYj5h
Devo 7e Transmitter - https://ebay.to/3hewcME
Paper clip - https://ebay.to/328C8jL
Battery charger - https://ebay.to/3aJmAa4

_______Amazon_______
Radiolink RC6GS 6 channel - https://amzn.to/2OENF7E
Radiolink RC4GS 4 channel - https://amzn.to/3bO7lPd
Radiolink R4FGM 4 channel reciever - https://amzn.to/3ljG3U9
Mini ESC - https://amzn.to/38EOjsP
1.5g Micro Linear servo - https://amzn.to/3eGQkZl
1.7g Rotating servo - https://amzn.to/3cCH1qI
LiPo battery 75mah - https://amzn.to/3tBEvbd
N10 dual shaft motor (buy from eBay instead. It is cheaper) - https://amzn.to/3eI78Pr
2 pin JST connector with wire - https://amzn.to/38LpSd9
Micro on/off switch - https://amzn.to/3qO7Zk5
M1 screws - https://amzn.to/3vwAjLE
Devo 7e transmitter - https://amzn.to/3czXeN9


Tools:
_______eBay_______
Ender 3 3D printer - https://ebay.to/3hh0VbS
Dremel Rotary Tool - https://ebay.to/2CKW7fT
Dremel chuck - https://ebay.to/3gd0ZYJ
Diamond Cutting disc - https://ebay.to/2FIEWwB
Weller Soldering Iron - https://ebay.to/3mjTx2q
Soldering Iron tips - https://ebay.to/35nQSOZ
Micro drill bits- https://ebay.to/2Ep8xu5
Mini taps set - https://ebay.to/2FORqmx
Side cutter - https://ebay.to/3j2nAJA
Fine tweezers - https://ebay.to/34hNg0s
Precision screwdriver set - https://ebay.to/31eQ9NB
Liquid Electrical Tape Black - https://ebay.to/3gi1bWE

_______Amazon_______
Ender 3 Pro 3d printer - https://amzn.to/3vtPQM4
Creality LD002R LCD Resin 3D Printer - https://amzn.to/3eJ5Pjp
Dremel rotary tool - https://amzn.to/3vu4kvl
Keyless chuck - https://amzn.to/3czvh8h
Weller Soldering Iron - https://amzn.to/3vwbJdN
Micro drill bits - https://amzn.to/38M469j
Mini needle files - https://amzn.to/3eOSTbX
Side cutters - https://amzn.to/3eHpVKK
Mini taps set - https://amzn.to/3qXkom4
Precision Tweezers Set - https://amzn.to/38EQr3N
Mini screwdriver set - https://amzn.to/38M4vZn
Liquid Electrical Tape Black - https://amzn.to/3cytGQd

There are some more tools that I use for the build. I will list them completely once I do an inventory of all the tools.

After searching and watching other videos on YouTube, I decided to change the steering mechanism a little bit. Previously, I bent a paper clip from the rotating servo to the hole on the knuckle and hoped it would "push and pull" the steering left and right as the servo is activated and rotated. This did not happen so I had to change by adding a straight piece of paper clip to the servo and having another paper clip that was 90 degrees from the hole on the steering knuckle. This yielded some way better results. Although, it it not perfect, but it will do. The other thing was, by doing this, I had to left the servo up by 0.1" and that made me loose a lot of space inside to pack the battery and the connectors. I may have to do away with the connectors.

I got lucky that I have some heat shrink that was just a tad smaller than the plastic wheels. I had to stretch the heat shrink over the wheels. With the heat shrink on the wheels, it was just like as the wheels were rubber. The grip and steering were perfect. Smooth driving on all surfaces.

The Hot Wheels diecast had a different design due to the shape of the body. I had to grind down the inside areas of the doors to fit the base cover. Even after so, the base cover did not fit will. I had to tape the bottom with clear tape to hold it to the body.

I am still trying to figure out how to connect the rear tail lights to the servo. For some reason, it seems like any channel the rear tail lights are connected to, they do not turn off or on. They are just on all the time. I tried setting the transceiver to a different channel and having it on a different setting so I can have a 0 to 100 output, but that did not work. I may have to move the rotating servo to a different pad on the receiver.