Centurion D5 Smart Evo sliding gate motor installation in Sebokeng Gauteng by Pottie 0837782288

Описание к видео Centurion D5 Smart Evo sliding gate motor installation in Sebokeng Gauteng by Pottie 0837782288

You have just found the best Centurion gate motor installer in Gauteng.
Pottie is a the best Centurion D5 Smart Evo gate motor installer in Sebokeng.
Pottie is a expert with 20 years experience in swing and sliding gate motor installations.
Its not common to find such a great gate motor specialist like Pottie.
Just call Pottie now on 083 778 2288 to effect your new Centurion Smart gate motor installation in Gauteng.
Pottie does, repairs on all types of gate motor systems especially the Centurion sliding gate motor range consisting of D3 Smart, D5 Smat Evo, D6 Smart, D10 Smart, D10 Smart Turbo and Centurion D20 Smart.
Once again, Pottie has shown that installations of gate motor systems are not just about the gate motor.
Proper gate guide brackets needs to be in place in order to allow the steel sliding/ swing gate to fully close safely.
Gate roller guides and brackets needs to be in place in order to guarantee safe operation of the stee sliding gate at all times.
Proper gate stoppers are needed to prevent any steel sliding gate from being derailed at any point in time, regardless of the force used on the steel sliding gate.

When all of the safety aspects are in place, then only should one start with the gate motor installation.
On this site, a concrete base was in place, but it was not level. Varius options were present in order to create a platform on which a Centurion D5 Smart Evo gate motor could be mounted.
It was decided that a 76mm x 38 mm rectangular tubing would be the perfect fit. The gate motor would sit just above ground level and nearly level, with the current paving.
The rectangular tubing was welded into place, onto a steel post next to it.
Steel braces consisting of 50x5mm flat bar was also used.
The flat bar was welded onto the steel gate track as and then onto the rectangular tubing.
A steel coach screw was then drilled into the concrete slab through the steel flat bar.
The steel brace was then bolted down into the concrete slab.

The Centurion D5 Smart Evo sliding gate motor steel base plate was spot welded into position and then welded down properly.
The gate motor was then bolted down onto the steel base plate. In a upright and level position.
The gate motor was also fitted parallel with the steel sliding gate.

The steel rack sections were joined by welding them together.
The steel rack was then welded onto the steel sliding gate.
3x 5x50 flat bar support brackets were welded onto the steel sliding gate as the gate has horizontal bars, which moves about much more compared to vertical bars.

Steel angle brackets were used to weld the steel rack onto the steel sliding gate.
The steel angle brackets were of 40x4x3mm in size and around 45mm long.
The steel angle brackets were fitted around 400mm apart from each other.
One must be well versed in welding, to attempt to weld a steel rack onto a steel sliding gate.

With all welded down, it was time for the electrical supply cable to be connected to the gate motor.
Power was turned on, and the battery charging voltage was checked before the batter was connected.
This is to check and verify that the battery will not be over charged or under charged.
A good lead acid battery charging voltage is around 13.80 volts dc up to 14,40 volts dc.
Anything more will damage the lead acid battery.
The gate motor was powered up.
The gate motor controller card is programmed via the my Centsys app and a blue tooth connection.
The gate motor limits were programmed as well as the remote transmitters.
It must be noted, that this gate motor controller card has no buttons present for any programming and one cannot open the steel sliding gate from the gate motor controller card.

With all programming done, the gate motor is tested and the site is handed over to the new client.
The gate motor is also locked with the gate motor keys.
The anti theft bracket is also fitted, to prevent the gate motor from being stolen.

Exquisite Security always goes the extra mile, here the gate motor serial number and clients contact details were engraved onto the gate motor.
Should the gate motor be stolen, which is unlikely, one can still trace the owner.

To know more about the Centurion D5 Smart Evo gate motors, just visit:
https://www.exquisitesecurity.co.za/i...

Комментарии

Информация по комментариям в разработке