In this How-To video for our Rvinyl, you're going to see how to wrap the front fender of a vehicle using this color change film and tools from our Rvinyl which are available here:
https://www.rvinyl.com/Fender-Wraps
The first step is to clean, spray Rapid Prep on a highly absorbent microfiber towel, take a tucking towel and place it inside the microfiber towel and go. After all, the tight gaps start at one point on the front fender and do a 360 degree loop where from one point all the way around back to it. This could mean opening up the hood to remove dust from the inside section there, as well as the front door as a lot of dirt and oil can build up on this inside gap. So work from top to bottom and be extra focused here.
Once all the outside edges are clean, then it's time to clean the main surface area. Spray Rapid Prep on the microfiber hotel one more time and then wipe it down from top to bottom. Now, with the cleaning process done, it's time to move on to the next stage, which is masking tape.
Once all the masking tape is set up the wrapping process can begin.
Place the piece on the fender with magnets, then take a Snitty and cut the material safely away. This means the knife won't touch the surface and there's no damage to the vehicle. Now, with the material prepped and trimmed, it's time to release the liner: here, starting at the top release at roughly six or seven inches fold the material under, no need to cut it. Then once the material is creased and laying flat, pick the material up and hook the upper corner. This will lock it in place and, by starting at the corners of the top, this means they'll be better quality - no tension. Lock it into the upper body line of the fender then pulled the liner low and flat underneath the vinyl. This means there's no dust coming onto the adhesive side, which will help keep a high quality finish.
Once the liner has been removed, the main section is time to glass it out. This means creating no wrinkles on the film, picking up nice and high and pull it along the body line nice and even so, pull from top and bottom. And once it hits the body line with even tension, lay it flat and lock it in with a thumb.
Now release the rest of the liner and pull towards the corner by pulling towards all the corner, the material will have a wrinkle free state. Once it's wrinkle free always apply the recessed areas first. This is called the palm technique, which was invented by the Wrap Institute by doing the palm technique. This means there'll be no adhesive lines so the quality of the finish will be great. So once the film is locked into this upper recessed area, now you can come back and finish the corners with the Avery Dennison Flextreme, pick the material up high and then hook the corner. This will mean the corners will be extra flat and look like paint.
So once the top section is finished, then it's time to squeegee any remaining air out from underneath the film using a monkey strip on a squeegee, then lock in the top edge.
Now the film can then be tucked deep into the base using the hard side of the squeegee and a Flextreme. It is very important to take the film as deep as you can. Always use a very sharp blade and keep the angle of the blade at a 10 degree angle towards the surface. This means it'll be held safely by the edge of the raised object and won't cut the paint below it. Make sure you always cut towards yourself and never away.
Once all the excess film has been cut away, retract the blade and pull the excess film away from the raised object and immediately tuck it in with the talking tool with all the materials safely on the main surface of the front fender.
It's now time to cut away the excess film on the edges. Always go around with the heat gun to relax the film on the edges, cut the corners first and when possible, always allow the blade to be guided along the edge on the opposite side of the front fender. This will allow around one quarter inch of film that can then be wrapped around for full coverage so the color wraps around the fender as well as for extra hold.
Once that section has been applied work to on another section. The tight gap by the front bumper and front fender should be tucked in and the masking tape allows the film to slide safely deep into the gap. Run the blade just in the middle of the gap, never cut directly on the surface, then remove the excess film and immediately come back in and seal the deal.
Now we can move into the top section: here by cutting on the opposite side alongside the hood that one quarter of an inch excess material is then tucked into the gap for full coverage and hold on a finger with application glove, then run a squeegee deep into the gap to seal the edge. Very straightforward.
To finish, simply spray the surface and wiping it down with a microfiber towel to remove any handprints and also double check that all the edges are sealed.
#Rvinyl #FenderWraps #JustinPate
Информация по комментариям в разработке